TROUBLESHOOTING | ||
|
|
|
| Observe all Safety Guidelines detailed throughout this manual |
|
|
|
|
PROBLEMS
(SYMPTOMS)
POSSIBLE
CAUSE
RECOMMENDED
COURSE OF ACTION
ARCLINK SYSTEM ERROR CODES
Err 263 No usable weld modes.
If all recommended possible areas of misadjustment have been checked
2.See the power source Instruction and the problem persists, Contact Manual for load welding pro- your local Lincoln Authorized Field
grams. | Service Facility. |
Below are errors implemented for the MAXsa™ 10.
Error | Source | UI Text | Reason |
Code |
|
|
|
|
|
|
|
N/A | User Interface | " Limits Exceed " | When a mode is selected with a work point low limit |
|
| "Gear Box Type" | greater than the high WFS limit. (no event is logged) |
|
|
|
|
28 | Feeder | “OUTPUT DISABLED” | The shutdown 2 input on the Feeder Board is open and |
|
|
| P.21 is selected for “Output Disable” |
|
|
|
|
83 | Feeder | " UI Shutdown 1 " | The shutdown 1 input on the Feeder Board is open. |
|
|
|
|
84 | Feeder | " UI Shutdown 2 " | The shutdown 2 input on the Feeder Board is open. |
|
|
|
|
Typical User Interface 3 digit error codes (not blinked on the status LED).
| Error | Source | UI Text | Reason | |||
| Code |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
213 |
| Power Source | User Interface could not communicate with control board | ||||
|
|
| is | in power source. | |||
215 |
| Feeder Board is | Either no feed head board is connected, being repro- |
| |||
|
|
|
| grammed or experiencing a fatal event. | |||
247 |
|
|
|
|
|
| |
| N/A | Arc control has a latched fault. The UI will indicate a | |||||
|
|
|
| Reset button needs to be pressed to clear the fault. | |||
274 |
| N/A | Weld set change required clearing of user memory. |
|
| ||
| 275 |
| N/A | UI memory could not be saved. Contact Lincoln Electric | |||
|
|
|
| Service Department for further support. | |||
276 |
| N/A | UI memory could not be restored. Contact Lincoln |
|
| ||
|
| User Interface |
| Electric Service Department for further support. | |||
|
|
|
|
| |||
277 |
| N/A | UI memories were converted due to change in number of | ||||
|
|
|
| UI parameters. Info only. | |||
|
|
|
|
| |||
278 |
| N/A | UI limits were converted due to change in number of UI | ||||
|
|
|
| parameters with limits. Info only. | |||
281 |
| (Varies based on the | Internal Error. Collect all displayed values and contact |
|
| ||
|
|
| error type and who | Lincoln Electric Service Department. | |||
|
|
| caused the error) |
|
|
|
|
282 |
| (Varies based on the | Internal Error. Collect all displayed values and contact |
| |||
|
|
| error type and who | Lincoln Electric Service Department. | |||
|
|
| caused the error) |
|
|
|
|
|
|
|
|
|
|
|
|
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
MAXsa™ 10 CONTROLLER
