Connecting LCD Cable | Matsushita CF-W5LWEZZ1 2 manual

9.3.2.7. Connecting LCD Cable

Connection

LCD Cable

Connector externals match

Affixation standard

PET Tape

Safety important parts

Inverter

Safety Work

affixes in a connector externals putting (wrapping) together.

	Safety Work
	The upper surface of the connector		Both sided tape
	is pressurized and affixes.		Both sided tape
	is pressurized and affixes.

Case		board
Case

Inverter box		OK
Inverter box

Inverter box

NG

The board must not float hooking the side.

ICD / Inverter cable

Connection

Safety Work

The flaking off paper is peeled off and then affixes on the connector. (pressurizes by the finger. )

40

Image 40

Matsushita CF-W5LWEZZ1 2 service manual Connecting LCD Cable

Contents

CF-W5 How to replace the fuse For U.K This apparatus must be earthed for your safety Laser Safety Information Page Page Contents Specifications Page Page Names and Functions of Parts Mini Port Replicator Connector Block Diagram Diagnosis Procedure Troubleshooting Flow Chart Error Diagnosis by Checking Beep Signal Sound Outline of Post Stuck key 02D0 System cache error Cache disabled When you execute the enhancing test When you execute an automatic testShift and left Shift keys Operation of PC-Diagnostic Utility Content of the setup is returned to the setting of the user PC-Diagnostic utility End methodSelection of tested device Test Item and Division of trouble GPS Wiring Connection Diagram Disassembly instructions Before disassembly, be sure to perform the following steps PreparationRemoving the Keyboard Preparation perform the .2.1. first Removing the HDD Removing the Top CasePreparation perform the .2.1., 9.2.2. first HDD Preparation perform the .2.1. to 9.2.3. first Removing the SW BoardFFC PAD FFC SW Removing the Touch Pad Removing the Disc CoverPAD FFC Removing the LCD Knob Removing the SpeakerRemoving the Solenoid Removing the Main Board Remove the DC-IN jack holder Removing the Wireless LAN Module Removing the Drive UnitRemoving the Antenna Board L,R Removing the USB Board Removing the Modem Removing the Card Bus EjectorPreparation perform the .2.1. to 9.2.4. and 9.2.11. first Preparation perform the .2.1. to 9.2.3. and 9.2.11. first Removing the LCD Unit Removing the Hinge CoverRemoving the LCD Unit and the LCD Rear Preparation perform the .2.1. to 9.2.4. and 9.2.18. first Removing the Inverter Board Removing the Wwan Antenna Board MAIN, SUB Removing the Wwan Board Assembly knowhow of the LCD Assembly of the LCD Front Putting LCD Insulator Putting TP Flexible Protection TapeLCD Assembly of the LCD Unit Putting LCD Side Dumpers Assembly of the LCD Dumper Bold Connecting LCD Cable Assembly of the Inverter and Putting Inverter Tapes Line processing LCD Cable Cable is processed to the LCD frame clamping Built-in order Safety work Putting Tapes of LCD Cable Assembly of the WM Cable Putting LCD Rear Cushions Assembly of the Wwan Board Putting Tapes for WM Cable Setting Spacer CU on Antenna Cover Next Assembly of the LCD Rear Assembly of the Hinge Cover L, R Assembly knowhow of the Main Board Putting tapes for Memory Sheet of top side Assembly of the MDC Modem Putting PET tapes Assembly of the Pcmcia Ejector Putting Main PW Sheet Assembly of the DVD FFC Assembly of the LAN CableDVD FFC Screw tightening of Main Board Line processing LAN cable Assembly of the W-LAN Module / Putting Memory Heat Sheet DXQT2+D25FNL Assembly of theMODEM Cable Putting Sheets Between cushion and addable Memory Processing 5mm 3mm Assembly of the W-LAN Sheet Assembly of the HDD FPC HDD FPC Assembly of the DC-IN Cable Setting the Main Board Wlan SW Boss B Assembly of the DVD Cover Assembly knowhow of the Top CaseAssembly of theBreak Lever Assembly of the Disk Cover Lock Putting Disk Cover Sheet Assembly of the SW Board Safety work Inserts under the rib Assembly of the Speaker Line processing Speaker Cable and putting Speaker Sheet Assembly of the LCD Knob Putting Hinge Buckup Sheet and LCD Knob Sheet etc Assembly of the Touch Pad Work Assembly of the Disk Cover Disk angle cushion Screw Order Assembly knowhow of the Bottom Case Setting Antenna Board and Line processing Assenbly of the Antenna Cover L Line processing HDD FPC Putting Tape and Sheet Treatment device Do not run aground to the pin Setting LCD Assembly knowhow of the BodyLine processing LCD Cable bottom case side Setting Disk Cover Assembly of the Top CasePET DXQT26+D8FCL DXQT2+E6FNL Assembly of the Disk Cover and Antenna Cover R Assembly of the Keyboard Order Assembly of the Heat Spreader Setting KeyboardPage Setting Dimm Cover Tightening screw of Bottom Case Putting Sheet Putting Labels Product back ratings signature board Assembly of the HDD / HDD Cover Putting Tapes for Wwan Antenna Cable Assembly of the Wwan Module Exploded View Screw tightening torque Cabinet Section SW6 Accessories REF. noMain Block Unit Packing Material LAN Switch Knob Hinge Cover R DFHR3F77ZA USB Cable FIX Sheet CF-W5LWEZZBM REF. no and Area Page Page Page Page Page Page Page Connector Ceramic CapacitorThermistor Diode DEDRB081L20 Diode LEDFUSE, 2A FUSE, 4A IC, Power Management Switch IC, USB Power SWIC, Q-SWITCH IC, FET Switch IDUCTOR, Common Mode Filter SwitchIC, Eeprom IC, SPI Flash Memory Transistor FETB1GBCFJN0037 Transistor B1GBCFNL0017 Transistor B1GBCFNN0042 Resistor Array B1GFCFEN0003 TransistorDEARA8AJ103M Resistor Array ERA3YEB123V RESISTOR, 1/16W, 12KΩ ERA3YEB203V RESISTOR, 1/16W, 20KΩERA3YEB243V RESISTOR, 1/16W, 24KΩ ERA3YEB333V RESISTOR, 1/16W, 33KΩ ERJ2GEJ100X ERJ2GEJ101X Page ERJ2GEJ105X RESISTOR, 1/16W, 1MΩ ERJ2GEJ104XERJ2GEJ106X RESISTOR, 1/16W, 10MΩ ERJ2GEJ153X RESISTOR, 1/16W, 15KΩ ERJ2GEJ154XERJ2GEJ201X ERJ2GEJ203X RESISTOR, 1/16W, 20KΩ ERJ2GEJ472X ERJ2GEJ473X RESISTOR, 1/16W, 47KΩERJ2GEJ474X ERJ2GEJ510X ERJ2RKD244X ERJ2RKD364XERJ2RKF1000X ERJ2RKF1001X RESISTOR, 1/16W, 1KΩ Slide Switch ERJ2RKF5101XERJ2RKF5102X RESISTOR, 1/16W, 51KΩ ERJ2RKF51R0X ERJ2RKF54R9X EVQPLDA15 Switch USB ConnectorTrance Crystal Oscillator DIP Switch IC, DC/DC ConverterB1GBCFNN0042 Transistor ERA3YEB303V RESISTOR, 1/16W, 30KΩ