Metrologic Instruments IS1000 , 3.1. Symbology Selection

IS1000 – Configuration Guide 22

START OF CONFIGURATION END OF CONFIGURATION

3.1. Symbology Selection

This code must be read to initialize

any new selection of symbologies

These six bar code symbologies are the most commonly used and are active by default.

Other symbologies can be selected on the next page.

• If no symbology is selected after the reading of New Selection code, the above six

symbologies will remain activated.

• Only the symbologies selected after the reading of New Selection code will be activated

• If New Selection code is not read before selecting another symbology, this will be added

to the six of above.

INTERLEAVED 2/5 *

NEW SELECTION

CODE 39 *

CODE 128 *

UPC/EAN *

EAN 128 *

! Note:

MONARCH/CODABAR *

Contents

Main IS1000 Series Radio Frequency Bar Code Reader Configuration Guide Metrologic Instruments GmbH Page Page Page Page Page Page Page Page Page 1.1. Default Configuration (factory setting) Default Configuration Page 2. COMMUNICATION MODES 2.1. RS232 2.1.1. Baud Rate 2.1.2. Data Bits 2.1.3. Parity 2.1.4. Stop Bits 2.1.5. End of Message Character 2.1.6. Time-Out Between Characters 2.1.7. ACK/NAK Protocol 2.1.8. XON/XOFF Protocol 2.1.9. RTS/CTS Protocol 2.1.10. PC-Term Mode 2.2. Keyboard-Wedge Page 2.2.1. End of Message Character 2.2.2. Upper / Lower Case Options 2.2.3. Types of Numeric Characters 2.2.4. Time-Out Between Characters 2.2.5. "WYSE" Time-Out 2.3. P.O.S. (Point Of Sale) Systems 2.4. Wand Emulation 2.4.1. Transmission Speed 2.4.2. Bar/Space Polarity 2.4.3. Idle State 2.5. Laser Emulation 3. SYMBOLOGIES 3.1. Symbology Selection Page 3.2. Code 39 3.2.1. Standard/Full ASCII 3.2.2. Full ASCII Extended 3.2.3. Multiread 3.2.4. Modulo 43 Check Character 3.2.5. Pharmacode or Pharma 32/39 3.2.6. CIP Code 39 3.2.7. Start/Stop 3.2.8. Modulo 43 Algorithm 3.3. Interleaved 2/5 3.3.1. Fixed Length(s) Authorized and Set Upon First Reading(s) 3.3.2. Fixed Length(s) Authorized and Set Using the Numeric Pad 3.3.3. Variable Lengths Authorized 3.4. UPC/EAN 3.4.1. Types of UPC/EAN Authorized 3.4.2. Transformations 3.4.3. Add-On Options 3.4.4. Leading Prefixes for P.O.S. Systems 3.4.5. Flag Option 3.4.6. Check Digit Options 3.4.7. Product Code 3.4.8. ISBN Conversion 3.5. Monarch/Codabar 3.5.1. Start/Stop 3.5.2. Concatenation 3.6. Code 128 3.6.1. Check Character 3.6.2. FNC2 Function 3.7. UCC/EAN 128 3.8. Standard 2/5 3.8.1. Number of Lengths Authorized 3.8.2. Start/Stop Types 3.9. MSI 3.9.1. Variable or Fix Lengths 3.9.2. Double Check Digit (Modulo 10) 3.9.3. Single Check Digit (Modulo 10) 3.10. Plessey 3.11. Telepen 3.12. Code 93 3.13. Matrix 2/5 3.13.1. Types of Start/Stop 3.13.2. Check Digit 3.13.3. Fixed or Variable Lengths 3.13.4. Setting the Authorized Lengths 3.14. IATA 3.15. BC 412 3.16. 3W7 3.17. Leading Identifiers 3.17.1. Identifier with One Character 3.17.2. Identifier with Three Characters 3.18. Decoding Selectivity Page 4. OPERATING MODES 4.1. Simple Acknowledgment 4.2. Host System Acknowledgment 4.3. On File / Not On File 4.3.1. Setting the On File Character 4.3.2. Setting the Not On File Character 4.4. Bell 4.5. Setting the Timers Default Value Operating Mode Timer T1 Timer T2 Timer T3 4.5.1. Timer T1 4.5.2. Timer T2 4.5.3. Timer T3 Page Page 6. APPENDIXES 6.1. Radio Parameters 6.1.1. Radio Channel Channel Number Frequency 6.1.2. Number of Re-transmissions 6.2. Adjustment of the Beep Sound 6.2.1. Laser Reader 6.2.2. Radio Base 6.3. Preamble / Postamble 6.3.1. Preamble Character 6.3.2. Postamble Character 6.3.3. Clear Buffer 6.4. Conversion of Characters 6.4.1. First Character Page 6.4.2. Second Character 6.5. Rolling Buffer Mode 6.6. Transmission of the Full ASCII Character Set 6.7. Displaying the Firmware Level 6.8. Code 39 Full ASCII Extended Table v t s u Page 6.9. Multiread character Table Page Page 6.10. Code 39 Full ASCII Table Page Page Page Page Page Page Page Page Page 6.11. Numeric Pad 6.12. Samples of Bar Codes