Miller Electric 185 DX manual

12-10. Typical Connections To Supply Standby Power

1

23

4

Have only qualified persons perform these connections according to all applicable codes and safety practices.

Utility

Electrical

Service

Transfer Switch

5

Essential

Loads

Fused

Disconnect

Switch

(If Required)

Welding

Generator

Output

Properly install and ground this equipment according to its Owner’s Manual and na- tional, state, and local codes.

.Customer-supplied equipment

is required if generator will sup- ply standby power during emergencies or power out- ages.

1Utility Electrical Service

2Transfer Switch (Double-Throw)

Switch transfers the electrical load from electric utility service to the generator. Transfer load back to electric utility when service is re- stored.

Install correct switch (customer- supplied). Switch rating must be same as or greater than the branch overcurrent protection.

3 Fused Disconnect Switch

Install correct switch (customer- supplied) if required by electrical code.

4 Welding Generator Output

Generator output voltage and wir- ing must be consistent with regular (utility) system voltage and wiring.

Connect generator with temporary or permanent wiring suitable for the installation.

Turn off or unplug all equipment connected to generator before starting or stopping engine. When starting or stopping, the engine has low speed which causes low volt- age and frequency.

5 Essential Loads

Generator output may not meet the electrical requirements of the prem- ises. If generator does not produce enough output to meet all require- ments, connect only essential loads (pumps, freezers, heaters, etc. − See Section 12-4).

OM-4415 Page 41

Image 45

Miller Electric 185 DX manual Typical Connections To Supply Standby Power

Contents

Processes OM-4415Description File Engine Drive From Miller to You Table of Contents Page Arc Welding Hazards Symbol UsageElectric Shock can kill HOT Parts can cause severe burns Buildup of GAS can injure or kill Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosion Compressed Air Hazards Engine Hazards HOT Parts can cause burns and injury Welding Wire can cause injuryFire or Explosion hazard Falling Unit can cause injury California Proposition 65 Warnings Principal Safety StandardsEMF Information Radiation can cause interference Signification des symboles − Consignes DE Sécurité − Lire Avant UtilisationUN Choc Électrique peut tuer DES Pièces Chaudes peuvent provoquer des brûlures graves LES Fumées ET LES GAZ peuvent être dangereuxLE Soudage peut provoquer un in cendie ou une explosion LE Bruit peut affecter l’ouïe ’EXPLOSION DE LA Batterie peuDES Organes Mobiles peuvent pro voquer des blessures LA Chaleur DU Moteur peut pro- voquer un incendie ’AIR Comprimé peut provoquer des blessuresRisque D’INCENDIE OU D’EXPLO- Sion DES Organes Mobiles peuvent provoquer des blessures LE Surchauffement peut endom- mager le moteur électriqueLES Fils DE Soudage peuvent provoquer des blessures ’EMPLOI Excessif peut Proposition californienne 65 Avertissements Principales normes de sécuritéInformation EMF Symbol Definitions − SpecificationsWeld, Power, And Engine Specifications − Definitions Dimensions Dimensions, Weights, And Operating AnglesDuty Cycle 100% Duty Cycle at 100 Amperes CC/DC Volt-Ampere Curves Standard Model Honda EngineDX Model Kohler Engine Auxiliary Power Standard Model Honda Engine Auxiliary Power DX Model Kohler EngineFuel Consumption Curves Generator Power Curves Power Output Standard Model Honda EnginePower Output DX Model Kohler Engine Installing Welding Generator − InstallationMovement Hazards Engine Prestart Checks − Standard Model Grounding Generator When Supplying Building Systems13 mm Full Gasoline Fuel Valve Open valve + − Engine Prestart Checks − DX ModelConnect negative − cable last Tools Needed 1/2 Stop engine before connecting to weld output terminals Connecting To Weld Output TerminalsSelecting Weld Cable Sizes 150 ft 200 ft 250 ft OM-4415 Controls Standard Models See Section − Operating the Welding Generator Description Of Controls Standard Models See Section Turn Engine switch to OffTo Start To Stop Controls DX Models See Section Description Of Controls DX Models See Section − Operating Auxiliary Equipment Generator Power Panel Receptacles Routine Maintenance − Maintenance Precleaner Paper Element Servicing Air CleanerStop engine Standard Model Shown Weld/Power Speed Adjustment Adjusting Engine Speed Honda-Powered UnitsIdle Speed Adjustment Stop Engine Close Adjusting Engine Speed Kohler−Powered Units Stop engine. Close fuel valveTools Needed Troubleshooting − TroubleshootingGenerator Power Welding Engine − Parts List Recommended Spare PartsRecommended Spare Parts Circuit Diagram For Standard Models − Electrical Diagrams Circuit Diagram for DX Models − Generator Power Guidelines Selecting EquipmentGrounding Generator To Truck Or Trailer Frame How Much Power Does Equipment Require? Grounding When Supplying Building Systems Approximate Power Requirements For Farm/Home Equipment Approximate Power Requirements For Industrial MotorsIndustrial Motors Rating Starting Watts Running Watts Farm/Home Equipment Rating Starting Watts Running Watts Contractor Rating Starting Watts Running Watts Approximate Power Requirements For Contractor Equipment How Much Power Can Generator Supply? Power Required To Start MotorSingle-Phase Induction Motor Starting Requirements KVA/HP x HP x 1000 / Volts = Starting Amperage Typical Connections To Supply Standby Power Cord Lengths for 120 Volt Loads Selecting Extension Cord Use Shortest Cord PossibleCurrent Load Watts Amperes Cord Lengths for 240 Volt Loads − Stick Welding Smaw Guidelines Stick Welding Procedure Electrode and Amperage Selection Chart Striking an Arc − Scratch Start TechniqueStriking an Arc − Tapping Technique Good Weld Bead Characteristics Poor Weld Bead CharacteristicsPositioning Electrode Holder 10-30 9090 End View of Work Angle Electrode Movement During Welding Conditions That Affect Weld Bead Shape Lap Joint Butt JointsTee Joint 16 in 30 1.6 mm Tack Welds Troubleshooting − Excessive Spatter Troubleshooting − PorosityWeld Test Possible Causes Corrective Actions Troubleshooting − Incomplete Fusion Troubleshooting − Lack Of PenetrationTroubleshooting − Excessive Penetration Troubleshooting − Burn-Through Troubleshooting − Waviness Of BeadTroubleshooting − Distortion Service Your distributor also givesSupport Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s