RS-232C SETTING

Set the RS-232C interface board setting by using the on screen menu of the VCR.

1Press the DISPLAY button to display MAIN MENU.

• “MAIN MENU” will appear.

2Turn the JOG dial to select “FIRST TIME SET UP”.

3Turn the SHUTTLE ring to the right .

• “FIRST TIME SET UP” menu will appear.

<MAIN MENU>

DISPLAY

TIME DATE SEARCH TIMER PROGRAM RECORDING SET UP REAR TERMINAL MAINTENANCE FIRST TIME SET UP Use JOG to select, and ENTER.

Press DISPLAY to exit.

<MAIN MENU>

DISPLAY

TIME DATE SEARCH TIMER PROGRAM RECORDING SET UP REAR TERMINAL MAINTENANCE

FIRST TIME SET UP Use JOG to select, and ENTER.

Press DISPLAY to exit.

4Turn the JOG dial to select “RS-232C”.

If “RS-232C interface board” is installed correctly, “RS-232C” item will appear on “FIRST TIME SET UP” menu.

N

If the “RS-232C” item does not appear, press the RESET button on the rear panel of the VCR.

5Turn the SHUTTLE ring to the right .

“RS-232C” setting menu will appear.

Select the parameter to be changed by using the SHUTTLE ring. Change its value using the JOG dial and then use the SHUTTLE ring to store the new value.

<FIRST TIME SET UP>

 

STOP

TAPE END

 

QUASI V-SYNC

 

ON

TAPE LENGTH

 

E-180

VIDEO MODE

COLOUR

PB HEAD SELECT

NORMAL

BUZZER

 

WRNG

TIME DATE ADJUST

 

 

RS-232C

 

 

 

 

 

 

 

 

<RS-232C>

 

1200

TRANSMISSION RATE

 

DATA BIT LENGTH

 

8BIT

STOP BIT LENGTH

 

1BIT

PARITY BIT

 

NONE

DELIMITTER<SEND>

 

CR

DELIMITTER<RECEIVE>

CR

VCR ADDRESS

 

NONE

 

 

 

1SETTING TRANSMISSION RATE

When the JOG dial is turned to the right, the display will be switched in the order of 1200(bps) } 2400(bps) } 4800(bps) }9600(bps) } 1200(bps) } ....

2SETTING DATA BIT LENGTH

When the JOG dial is turned to the right, the display will be switched in the order of 8 BIT } 7 BIT } 8 BIT } ....

3SETTING STOP BIT LENGTH

When the JOG dial is turned to the right, the display will be switched in the order of 1 BIT } 2 BIT } 1 BIT } ....

4SETTING PARITY BIT

When the JOG dial is turned to the right, the display will be switched in the order of NONE } ODD } EVEN} NONE } ....

N

The Parity bit cannot be used when the DATA BIT LENGTH is set to 8.

5SETTING DELIMITER<SEND> (Setting a character marking the end of a command.)

When the JOG dial is turned to the right, the display will be switched in the order of CR } CR•LF } CR } ....

6SETTING DELIMITTER<RECEIVE> (Setting a character marking the end of a status or error code.) When the JOG dial is turned to the right, the display will be switched in the order of CR } CR•LF } CR } ....

7SETTING VCR ADDRESS (Setting the ID number of the VCR)

When the JOG dial is turned to the right, the screen display will be switched in the order of NONE } VCR01 } VCR02} VCR03 } ... } VCR14 } VCR15 } VCR16} NONE } ....

When controlling only one VCR via the personal computer, “VCR ADDRESS” is set to “NONE”.

When two or more VCRs are to be controlled in series, each VCR must have a unique VCR ADDRESS (from VCR01 to VCR16).

N

Set the communications parameters (items 1 - 6 above) to the same values as the controlling personal computer or other equipment. Each VCR must have the same settings when multiple VCRs are connected.

29

Page 29
Image 29
Mitsubishi Electronics HS-S8300E(BRS) operation manual RS-232C Setting, Setting Transmission Rate, Setting Data BIT Length