Manuals / Mitsubishi Electronics / TV and Video / VCR

Mitsubishi Electronics HS-S8300E(BRS) operation manual Connecting with Other Equipment, Sensor

Models: HS-S8300E(BRS)

1 42

Download 42 pages 28.02 Kb

Page 7

CONNECTING WITH OTHER EQUIPMENT

CCTV
CAMERA
	VIDEO
	OUT
SET IN
SENSOR			VIDEO
SENSOR				IN
	SET RST	REC	GND ALM MODE	CLK CALL
	IN		OUT	RESET
MIC	IN	OUT		REMOTE
	AUDIO		IN	OUT
			VIDEO
MIC IN			AUDIO	VIDEO
			OUT	OUT

MIC

IN

RS-232C

IN OUT

S-VIDEO

OUT

VIDEO IN

AUDIO IN

MONITOR

VERTICAL ADJUSTMENT (Correcting picture vibration at the top and bottom)

The picture vibration can be reduced or eliminated by the following steps.

1If the vibration occurs in still, slow motion, fast playback (x2) or normal playback in 12H - 960H or 0H mode, playback a tape which is recorded in 3H mode with this VCR and press the PAUSE button.

If the vibration occurs during normal playback in L12H or L24H mode, playback a tape in each playback mode.

2Press the VERTICAL ADJUST (+) or (-) button to reduce or eliminate the picture vibration.

N

•When QUASI V-SYNC is set to “OFF”, the picture vibration is not adjustable with the VERTICAL ADJUST buttons.

MONITOR TO BE CONNECTED

•Connection with a CCTV monitor (for surveillance) is recommended.

•Connecting with some monitors may cause picture vibration and/or picture distortion at the top or bottom of the image during still or normal playback.

A domestic Television used as a Monitor may be unable to provide a stable picture without vibration and distortion.

7

Image 7

Mitsubishi Electronics HS-S8300E(BRS) operation manual Connecting with Other Equipment, Sensor

Contents

VHS HS-S8300EBRS Unplugging the Mains Lead When not in USEInstallation Location Condensation is the Enemy of Video Recorders Features Contents Front View Features and FunctionsFluorescent display Fluorescent Display REC Reset button Features and FunctionsRear View Sensor Connecting with Other Equipment Present time display will appear Setting the MenusPresent Time Display Display Timer ProgramTime Date Search Recording SET UP Setting the MenusRear Terminal Maintenance First Time SET UP Display mode Setting the Present TimeFRI Setting the Present Time to the Exact Second Setting the Present Time Preventing Accidental Erasure Loading and Unloading the Cassette TapeLoading Unloading Recording Check Function REC ModeLock Mode Manual Recording Recommended Number of Tape USE Stop Rewind Repeat AlarmprotRepeat Recording Number of Tape USE Repeat REC Times Connection Manual RecordingONE SHOT/INTERVAL Recording Synchronous Recording Additional Features Timer Recording Symptom Fault Action Order to Avoid Mistakes When Using the Timer 1st VCR Alarm RecordingAlarm Recording Connection External Time Clock Adjustment Emergency Recording Setting for Alarm Recording Index Search Alarm RecordingAlarm Record Time Display Locating the Start of Alarm Recordings Playback Playback ModeAudio Playback Still Picture Special Effects PlaybackShuttle Ring Direct Shuttle Ring When the picture is vibrating Adjustment During PlaybackTracking Adjustment Picture Quality Adjustment Configuring the Time Lapse VCR Using with the Personal ComputerConnecting the VCR to a personal computer Setting Stop BIT Length RS-232C SettingSetting Transmission Rate Setting Data BIT Length Physical protocol of RS-232C Using with the Personal ComputerConnecting to a Personal Computer Data Communications Settings Command carried out Command Commands sent to the VCR FormatPower on command Command received Command carried out VCR02 Command ParameterCommand for fast forwarding VCR02 Command received VCR02 Commands and Responses 171=TIME Date Adjust + STOP=0, REWIND=1, REPEAT=2 +0=SERIES, 1=REC-START/STOP =SYNC REC Error codes Display Self Diagnostic FunctionFluorescent Monitor Cause Remedy To Turn OFF the Indication Symptom Remedy Before Calling for ServiceIs the Lock indicator illuminated? Control INPUT/OUTPUT Signals and Circuits Circuit Control INPUT/OUTPUT Signals and CircuitsLabel B-7 Connectors Specifications 872C193C3