Mitsubishi Electronics WD-60C8 Receiver Sound System Using the TV’s Audio Output, DVD player

243. TV Connections

A/V Receiver (Sound System) Using the TV’s Audio Output

Most setups require either a digital audio cable or analog stereo audio cables. To send audio from TV channels received on ANT 1, ANT 2, or devices con- nected directly to the TV, you must use one of the con- nections shown below.

The TV makes all audio available in digital and analog formats:

•Analog audio coming into the TV is available as output in digital stereo format on the DIGITAL AUDIO OUTPUT jack.

•Digital incoming audio is available as analog output on the AVR AUDIO OUTPUT L and R jacks.

Usually, only one of the following audio connections is required:

•To connect an analog A/V receiver

Connect left (white) and right (red) audio cables from AVR AUDIO OUTPUT L and R on the TV back panel to the TV AUDIO INPUT on the A/V receiver.

•To connect a digital A/V receiver with Dolby Digital surround sound and PCM audio support:

Connect one end of the digital audio cable to DIGITAL AUDIO OUTPUT on the back of the TV. Connect the other end to the COAXIAL DIGITAL INPUT on the back of the A/V receiver.

					AVR
	3D				AUDIO
57 CBDL QBOFM					OUTPUT
	EMITTER
	GLASSES
				L
ANT 2	AVR								HDMI
	AUDIO								VIDEO: 480i/480p/720p/1080i/1080p
	OUTPUT	DVI/PC INPUT			R AUDIO L	VIDEO			AUDIO: PCM STEREO
			AUDIO	R
	L	R		L			3	IR-NetCommand	PC: VGA, W-VGA, SVGA, W-SVGA,
							INPUT		XGA, W-ZGA, SXGA, 720p/ 1080p
								Output / External
					Pb	Pr	INPUT2	Controller Input	HDMI
DIGITAL	R			Y				1	2	3
AUDIO				Y/VIDEO	Pb	Pr
OUTPUT	DIGITAL		R AUDIO	L	(480i / 480p / 720p / 1080i)		1	INPUT 3
							INPUT
								S-VIDEO
	AUDIO
	OUTPUT

4UFSFP
BOBMPH
DBCMFT GPS
DPOOFDUJOH
BO
BOBMPH
"7
SFDFJWFS

%JHJUBM
DPBYJBM
DBCMF GPS
DPOOFDUJOH
B
EJHJUBM
"7
SFDFJWFS

015*$"-
*/165

$0"9*"-
*/165

"7
SFDFJWFS
CBDL
QBOFM

Figure 11. Connecting the TV to an A/V receiver

Note:

•On rare occasions, an HDMI signal may be copy-restricted and cannot be output from the TV as a digital signal. To hear these copy- protected signals through the A/V receiver, use the connection for an analog A/V receiver.

•Check the A/V receiver’s Owner’s Guide for information concerning use of the digital input and switching between digital sound and analog stereo sound from the TV.

A/V Receiver with HDMI Output

Required: One HDMI-to-HDMI cable

This option allows you to view content from devices connected to an A/V receiver. The A/V receiver can send audio and video to the TV over a single HDMI cable. You can use an HDMI connection as described here in addition to an audio connection from the TV’s audio output.

You may be able to use the TV’s remote control (with slide switch set to TV) to operate connected CEC- enabled HDMI devices. Experiment with your equip- ment to determine which functions are available to the TV’s remote control. See Appendix E, “NetCommand HDMI Control of CEC Devices” on page 77.

736 or 835 Series TV: This setup allows you to use NetCommand-controlled audio and video switching over the HDMI cable. See “A/V Receiver Control: Automatic Audio and Video Switching via HDMI” on page 61.

3D

GLASSES

EMITTER

L

R

AVR

HDMI

AUDIO

OUTPUT

DVI/PC

INPUT

R

AUDIO

L

VIDEO

VIDEO: 480i/480p/720p/1080i/1080p

AUDIO: PCM STEREO

L

R

AUDIO

L

3

IR-NetCommand

PC: VGA, W-VGA, SVGA, W-SVGA,

INPUT

XGA, W-XGA, SXGA, 720p/ 1080p

Output / External

HDMI

ANT 2 / AUX

Pb

Pr 2

Controller Input

R

Y

1

2

3

ANT 1 / MAIN

INPUT

DIGITAL

Y/ VIDEO

Pb

Pr

AUDIO

1

OUTPUT

DIGITAL

R

AUDIO

L

(480i / 480p / 720p / 1080i)

INPUT

S-VIDEO

INPUT 3

AUDIO

OUTPUT

TV back panel

Optional
analog or		A/V receiver
digital audio
		with HDMI
connection
L R AUDIO		output
DIGITAL	HDMI OUT
		VCR
High-definition
DVD player	DVD player
Cable box

Figure 12. A/V receiver connected to the TV with an HDMI cable may offer special control capabilities.