Mitsubishi Electronics WD-65835, WD-60735 Controlling A/V Receiver Sound Volume, Setup Procedure

142. TV Setup

2. TV Setup 15

Setting Up TV Inputs, continued

Setup Procedure

1.Connect your devices to the TV, making note of which TV input is used for each device. See chapter 3, “TV Connections.” The TV and the devices can be either on or off when connecting.

Next perform

IR “learning” (if

First select a available). device type.

Sample Auto Input Sensing screen

2.Power on the TV if not already on. When the TV detects a connection, the Auto Input Sensing screen opens.

•Most Device Types: Specify the device type.

a.In the Auto Input Sensing screen, press to move through the device list to select the device type connected to the input. The device type you select here will appear as an icon in the Input Selection menu.

b.736 and 835 Series Models: To perform NetCommand “learning” after selecting the device type, highlight the Learn icon and press ENTER. See chapter “Initial NetCommand Setup for Most Devices,” page 53.

•A/V Receiver: The TV can detect audio connections on the DIGITAL AUDIO OUTPUT jack and the right (red) analog AVR AUDIO OUTPUT jack.

736 and 835 Series Models: To perform NetCom- mand “learning” now, highlight the Learn icon in the Auto Output Sensing screen and press ENTER. See “Setting Up NetCommand Control of an A/V Receiver,” page 57.

•HDMI Devices Compatible with the TV’s NetCommand for HDMI Feature (all models): Compatible HDMI devices with CEC enabled are often recognized automatically by the TV. After con- necting the device, you may briefly see the standard Auto Input Sensing screen shown above before the TV recognizes the device type. The TV’s remote control may operate some device functions without further setup. To add control over more functions:

-- All Models: Program the TV’s remote control to operate the device.

--736 and 835 Series Models: Perform NetCommand IR “learning” to add functions.

3.Press EXIT to close the Auto Input Sensing screen. The TV will then display the Auto Input Sensing screen for the next connection it finds.

More About Auto Input Sensing

•Choose a different name for each input.

•Antenna inputs (ANT 1/ANT 2) are never detected, although you can turn off unused antenna inputs in the Inputs > Name menu.

•You can change the device type at a later time using the

Inputs > Name menu (page 47). Any “learned” NetCom- mand IR codes will be erased, however.

Changing Devices on an HDMI Input:

1.Disconnect the HDMI device.

2.Turn off the HDMI input in the Inputs > Name menu.

3.Connect the new device and the Auto Input Sensing screen will display. If you want the device under NetCommand IR control, perform NetCom- mand “learning” for the new device.

Note for Analog A/V Receivers

When you disconnect an analog A/V receiver, be sure to manually change the Speakers setting to TV to hear sound from the TV speakers.

Controlling A/V Receiver Sound Volume

Although the TV detects when you connect an A/V receiver, you must use one of the methods below to control sound volume from the A/V receiver.

With a Standard TV Setup (all models)

•Recommended Method: Program the TV’s remote control for your A/V receiver and enable the Audio Lock feature. See Appendix C, page 65.

•Program the TV’s remote control for your A/V receiver and set the TV remote’s slide switch to the AUDIO posi- tion to control A/V receiver volume. Set the switch back to the TV position to control the TV.

•Use the remote control that came with the A/V receiver.

With an HDMI CEC-enabled A/V Receiver (all models)

The TV’s remote control may control some or all functions of the A/V receiver without further setup. Connect the A/V receiver to the TV with an HDMI cable and test the TV’s remote control with the slide switch in the TV position.

With NetCommand Control of an A/V Receiver (736 and 835 series models)

•Set up NetCommand control of the A/V receiver’s volume functions in the Inputs > AVR menu. The TV’s remote will then automatically control A/V receiver volume. See page 57.

•Use any of the methods described for the standard

TV setup.

About Home-Theater Control Systems

This summary outlines the control methods available using the TV’s remote control. You may wish to use one or more of these methods for your home theater.

Case 1: The source device you want to control is connected directly to the TV

•If the source device has CEC capability:

a. Check the device’s owner’s guide and enable the device’s CEC functionality				HDMI
before connecting to the TV’s HDMI input. Wait for the TV to recognize the				Cable
	CEC-Enabled
device and switch to it.
	Source Device					TV
b. Experiment with the TV’s remote control (slide switch set to TV) to deter-
mine which device functions it can operate. See “NetCommand for HDMI
Devices” on page 28.
• If the TV is a 736 or 835 series model (any connection type):
Set up NetCommand IR control of the source device’s keys as desired. See “IR
		Any Connec-
Emitter Placement,” page 52, and “Initial NetCommand Setup for Most Devices,”
			tion Type
page 53.
• For any TV model (any connection type):	Source
					TV
Program the remote control to operate the source device. To control the device,	Device

set the slide switch to the correct position for the device type. See Appendix C, “Programming the Remote Control.”

Case 2: The source device you want to control is con- nected to an A/V receiver connected to the TV

•If the A/V receiver has CEC capability:

a.Check the A/V receiver’s owner’s guide and enable the A/V receiver’s CEC functionality before connecting to the TV’s HDMI input. Wait for the TV to

recognize the device and switch to it.		CEC-Enabled
b. Try using the TV’s remote control to operate volume and mute functions.		Source Device
				HDMI
See “NetCommand for HDMI Devices” on page 28.
				Cable
c. If the connected source device has CEC capability:
i)	Enable the device’s CEC functionality before connecting to the A/V	CEC-Enabled
	receiver’s HDMI input. Wait for the TV to recognize the device and switch	A/V Receiver
	to it.			HDMI
ii)	Test using the TV’s remote control to determine which device functions it			Cable
	can operate.		TV

Note: If the source device is connected to the A/V receiver by another con- nection type (e.g., component video, S-video), see the alternative control methods below.

•If the TV is a 736 or 835 series model (any connection type):

a. Set up NetCommand IR control of the A/V receiver’s keys as desired. See

“IR Emitter Placement,” page 52, and “Setting Up NetCommand Control of
an A/V Receiver,” page 57.
		Source
b. Set up NetCommand IR control of the source device’s keys as desired.
		Device		Any Connec-
See “Initial NetCommand Setup for Most Devices,” page 53.
				tion Type
For the special case of NetCommand IR control of a device connected to an
HDMI A/V receiver, see “NetCommand IR Control of a Device Connected to an	A/V Receiver
				Any Connec-
A/V Receiver with HDMI Output,” page 61.
				tion Type
• For any TV model (any connection type)
			TV
a. See Appendix C, “Programming the Remote Control.”
b. Program the remote control to operate the A/V receiver. To control the A/V
receiver, set the slide switch to AUDIO.

c.Program the remote control to operate the source device. To control the device, set the slide switch to the correct position for the device type.