VENT INSTALLATION
MANIFOLD REMOVAL AND INSTALLATION
The manifold is shipped attached to insert. It may be removed to allow tight installation. Mani- fold may be loosened and rotated for desired pipe location.
Chimney
Manifold
Flex Vent | Chimney |
|
1.Remove brick liner and baffle.
2.Remove manifold. Place manifold
in fireplace.
3. Route flex vent through chimney from above. See Figure 10. Leave an extra 3" (914mm) at the top.
4. Attach flex vent to manifold. See Figure 11. Seal with silicone and attach with screws.
Extra 3" (914mm)
Flex Vent
Vent
Termination
Bracket | Excess |
|
Nut | Flex Vent | Manifold |
Chimney
Chimney
Figure 10 - Placing
Manifold Into Fireplace
5. Place manifold in an upright position. Have someone pull on the excess flex vent. Figure 12. Temporarily attach flex vent to top of chimney. Leave some extra slack in flex vent.
Slack in
Flex Vent
Manifold
| Figure 11 - Attaching |
|
| ||||||||||||||||||||||||||||||||
| Flex Vent to Manifold |
|
| ||||||||||||||||||||||||||||||||
6. | Slide insert into place. Guide |
|
| ||||||||||||||||||||||||||||||||
| the manifold over the insert |
|
| ||||||||||||||||||||||||||||||||
| until it is fully in place. |
|
| ||||||||||||||||||||||||||||||||
| Figure 13. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
7. | Remove any slack from flex |
|
| ||||||||||||||||||||||||||||||||
| vent. Attach manifold to insert. |
|
| ||||||||||||||||||||||||||||||||
| Figure 13. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
8. | Remove any excess | slac |
| k |
| in |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
| flex line. Attach vent termina | - |
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||||||||||||
| tion. Figure 13. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||||||||||||
| Excess Sla |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| ck T |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||
| aken |
|
| ||||||||||||||||||||||||||||||||
|
| Out of Flex Vent |
|
| |||||||||||||||||||||||||||||||
9. | Replace | Manifold |
|
| |||||||||||||||||||||||||||||||
| baffle and | Bracket |
|
| |||||||||||||||||||||||||||||||
| brick liner. | Nut |
|
|
Insert
Figure 12 - Pulling On | Figure 13 - Sliding Insert |
Excess Flex Vent | Into Place |
16 | 57D0016 |