Camera Test | Motorola i860 manual

FIELD LEVEL TEST MODES AND PROCEDURES: Camera Test

8.15Camera Test

Use this test to check camera module. Symptoms: Bad view finder (noise, poor color, synchronization error).

Power up

the unit.

Enter the

Model Assembly

(MA) Test Mode.

	Verify				Fail	Replace
	that the viewfinder					Replace
	that the viewfinder					the camera module
	shows the captured					the camera module
	shows the captured					and repeat the
	image correctly.					and repeat the
	image correctly.					test.
						test.

	Pass					Pass
	Pass

Unit passed test. Look for system, coverage, accessory, or software problems.

Fail

Replace

the main FPC Fail

and repeat the test.

Pass

Replace the main board.

8-16	68P80400P73-A

Image 95

Motorola i860 manual Camera Test

Contents

Page I860 Manual Revisions Safety and General Information Medical Devices Electro Magnetic Interference Compatibility Cleaning and Drying Considerations Accessory Safety Information Safety and General Information Model Numbering System Model Information General Receiver Transmitter Model Specifications Contents Chapter Chapter Field Level Test Modes Procedures Appendix a Ordering Replacement Parts How This Manual Is Organized PrefaceWho Should Use This Manual Related Publications Conventions Used in This Manual DEN Digital Modulation Technology Overview Spectrum of i DEN Quad 16QAM RF Transmission Bursts DEN Voice Compression Technology Calling Area Coverage Removing and Inserting a SIM Card Global Positioning System GPS SectionSIM Cards To insert a SIM card Figure To remove a SIM card Figure Component Views COMPONENTS, ICONS, and Indicators Main Menu Icons Display Icons Status Icons Abc d efg d Opqr s Call Icons DEF Outbox Icons Contacts Type Icons This page intentionally left blank DISPLAYS, MESSAGES, and Alerts Power-Up Sequence Messages Power-Down SequenceSelf-Test Errors Self-Test Reset Errors Message Cause Action Service MessagesService Messages Alert Tones Tone Low High Freq Cadence When Tone OccursAlert Tones Alert Tones To set unit to vibrate for all calls Using the Optional Vibrate FunctionVibrator Settings Mode Cadence From the main menu, select Settings 2-Way Radio Alert Type This page intentionally left blank Reference Unit Preparing for Basic Level TestingReference Accessories Test Equipment This page intentionally left blank Test Conditions Reset ConditionBasic Level Checks and Self Tests Customer Care To clean the unit approximately 3 minutes Basic-Level Test ChecklistPreventive Maintenance Basic-Level Test Checklist SIM card swap test time is approximately 5 minutes Mechanical and Electrical ChecksSIM Card Swap Test Shock and pressure test time is approximately 3 minutes Lockup test time is approximately 6 minutes Accessory Swap TestAccessory swap test time is approximately 5 minutes Lockup Test To test this function Battery Connections TestTesting the GPS Receiver Battery connections test time is approximately 5 minutes Voltage recognition test time is approximately 4 minutes Voltage Recognition TestCamera Test Passcode test time is approximately 5 minutes TroubleshootingSelf-Test Procedures Passcode Test Phone Calls Features Programming Menu Settings CheckSettings check test time is approximately 10 minutes Way Radio Options Personalize Volume Features From the main menu, select Settings Security SIM PIN Security Features From the main menu, select Settings Advanced Headset/Spker Advanced Features Call performance test time is approximately 7 minutes Call Performance Test This page intentionally left blank Test Modes Basic Level Test Modes and ProceduresEntering Debug Mode To enter debug mode Name Description Display ScreensDisplay Screens To enter test mode Entering Test Mode To perform the audio loopback test test time approx min Test Mode Test ProceduresAudio Loopback Test To monitor the data in the unit ESN and Imei Matching TestEngineering Debug Check To perform the matching test test time approx min Software choice 68P80400P73-A Programming the i 860 Unit Technician Test Procedures Data Cable Programming Setup Connecting the Unit to the RSS Workstation To access the codeplug Help topic in Windows Codeplug Repair ProcedureCodeplug Troubleshooting Preparing Equipment for Testing Preparing for Field Level Testing Connecting an i DEN Unit to the R-2660 Using RSS Coaxial Cable In/Out Type To connect the unit to the R-2660 Field Value To enter Initial Registration modeOperating the R-2660 RF Zone Fields and Values Disassembling and Reassembling the Unit Remove Battery CoverInstall SIM Card Required Tools T-4 Torx bit Antenna Back Housing Required Tools Black stick Coin Cell Main Board, Microphone Seal, and Keypad Remove Flip Assembly Flip AssemblyPage Install Page Exploded View and Parts List Description Part Number Reference Component Parts ListComponent List Exploded View This page intentionally left blank Field Level Test Modes and Procedures Required Test Equipment Field-Level Test Checklist Done Technical Tests Pass Fail Field-Level Test Checklist Registration/Call Test See the Strong Signal Environment section SQE Test SQE Reference Chart See Entering Test Mode Press Menu, Edit TX Power Test Fail BER Test Power-Up Test Keypad Test Use this test to check the audio portion of the unit Audio Test No reset Reset Reset Test To perform the reset log test Reset Log Test Model Assembly MA Test Mode Test Model Assembly MA Test Mode Test Use this test on a unit to check functionality of the GPS GPS Receiver Camera Test Domestic Orders Ordering Replacement Parts and KitsCustomer Service Replacement Parts Description Kit Number Replacement KitsTable A-2. i 860 Replacement Kits Vehicle Power Adapters Description Part Number Recommended Test Equipment and ToolsTable A-3. Recommended Test Equipment and Tools Name Part Number Description Recommended Programming EquipmentTable A-4. Recommended Programming Equipment Table A-5. Recommended Software This page intentionally left blank Bcch Index QAM RSS Vselp @6880400P73@