SGW-250SS — CONTROLS AND INDICATORS
Figures 5 and 6 show the location of the controls and indicators. The functions of each control or indicator is described below and on the preceding page.
1.Welding Type (Wire/Stick) Selector Switch (CV/CC) – Turn this selector switch to either the CV or CC for welding. DO NOT turn this switch under load.
2.Current Range Selector Switch (CV/CC) – Turn this selector switch to either the CV or CC for welding. DO NOT turn this switch under load.
3.Current Control (CC) Adjustment Knob – Use this control to adjust welding current. Low scale (50~120 amps), High scale (90~250 amps). This function will not work in the CV mode.
4.Voltage Control (CV) Adjustment Knob – Use this control to adjust the welding voltage. This function will not work in the CC mode.
5.Idle Control Switch – Regulates the engine speed when the generator is under load.
6.Hour Meter – Indicates number of hours the welder has been in use or engine has been running.
7.Oil Filler Port – Use this port when adding oil to the engine.
3 | 2 | 5 | 6 | 7 | 8 |
8.Engine Air Cleaner – Prevents dirt and other debris from entering the fuel system. Lift locking latch on air filter cannister to gain access to filter element.
9.Main Circuit Breaker – This
10.ON/OFF Switch – This switch is used to start and stop the engine. Must be in th ON position (up) when starting the engine. Place in the OFF position (down) to stop the engine.
11.Start Button – Press and hold this
12.Oil Filter – Provides oil filtering for the engine.
13.Fuel Cap – Remove this cap to add fuel. Add only clean unleaded fuel. Always keep an adequate amount of fuel in the tank. DO NOT top off. Wipe up any spilled fuel immediately.
14.Battery Terminals – Connect these terminals to the battery. Always pay close attention to the polarity of the terminals when connecting to the battery, RED (positive), and BLACK (negative).
15.Battery – Provides +12 VDC power for the generator. When replacing battery (12V 35 AH) use only recommended type battery.
|
| ON | WHISPERWELD |
|
|
| |||
|
|
|
| SGW- |
|
|
| 10 | |
|
| OFF |
| 250SS |
|
| |||
|
|
| POWERED by |
|
|
| |||
|
| IDLE CONTROL | QUARTZ |
| |||||
|
| HONDA |
| ||||||
1 |
|
|
| AC CIRCUIT |
|
|
|
|
|
|
|
| BREAKER | HOUR | METER |
|
|
| |
|
|
|
|
| ON |
|
|
|
|
|
|
|
|
| OFF |
|
|
|
|
|
|
|
|
| OPERATION |
|
|
| |
|
|
|
|
| SWITCH |
|
|
| |
|
|
| MQ POWER | START |
|
|
|
| |
|
|
|
|
|
|
|
|
| |
4 | 9 |
|
|
| BUTTON |
|
|
| |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| . |
|
|
|
|
|
|
|
| Source | Professionals |
|
|
|
|
|
|
| Power |
| |
|
|
|
|
|
|
|
|
| |
| MQ | POWER |
| 11 | |||||
|
|
|
| ||||||
|
|
|
|
|
MQ POWER
14 12
13
15
Figure 5. SGW250SS Components 1
PAGE 20 —