Terminal Panel Features |
|
|
|
8 | 9 | 10 13 | 12 |
3 |
|
|
|
2 |
|
|
|
1 | 4 | 7 | 11 |
| |||
|
|
| |
5 | 6 |
|
|
1.RGB1 IN / Component Input Connector (Mini
RGB1 AUDIO Input Mini Jack (Stereo Mini)
This is where you connect the audio output from your computer or DVD player when connected to the RGB1 input. A commercially avail- able audio cable is required.
2.RGB2 IN / Component Input Connectors (BNC)
Connect R,G,B,H (Horizontal sync) and V (Vertical sync) outputs of external equipment.
If using a component with a combined sync (SYNC) output, connect it to the H/V terminal.
When using luminance and
NOTE: The RGB IN 2 does not support Plug & Play.
RGB2 AUDIO IN Mini Jack (Stereo Mini)
This is where you connect audio output from your computer or DVD player connected to the RGB2 input. A commercially available audio cable is required.
3.DVI IN Connector (24 pin)
This connector can be used to accept a digital signal output from a computer or other sources with a DVI connector.
DVI AUDIO Input Mini Jack (Stereo Mini)
This is where you connect the audio output from your computer when connected to the DVI input. A commercially available audio cable is required.
4.RGB OUT Connector (Mini
You can use this connector to loop your computer image to an exter- nal monitor from the RGB 1 or 2 input source.
The RGB analog signal set on RGBOUT Terminal is output during idle mode. See pages
RGB AUDIO OUT Mini Jack (Stereo Mini)
Connect an additional audio equipment here to listen to audio com- ing from your computer connected to RGB1, RGB2 or DVI input. Note that there is no audio output from this jack during Standby and Idle.
5.
Here is where you connect the
NOTE:
These are your left and right channel audio inputs for stereo sound from an
6.VIDEO IN Connector (RCA)
Connect a VCR, DVD player, laser disc player, or document camera here to project video.
VIDEO AUDIO Input Jacks R/L (RCA)
These are your left and right channel audio inputs for stereo sound from a Video source.
7. AUDIO OUT Jacks R/L (RCA)
You can use this connector to output sound from the currently se- lected input source (RGB 1, RGB 2, DVI (DIGITAL), Video or
8. USB Port (MOUSE/HUB) [Type A]
Connect the supplied USB mouse.You can operate the menu or Viewer with the USB mouse via this port.
•A
9.USB Port (PC) [Type B]
Connect this port to the USB port (type A) of your PC using the sup- plied USB cable. You can operate your computer's mouse functions from the remote control. This port also serves as a PC Control port by using Dynamic Image Utility 2.0 included on the supplied CD- ROM.
10. REMOTE (Mini Jack)
Connect your remote control cable here for wired operation.
11. PC CONTROL Port
Use this port to connect your PC to control your projector via a serial cable. This enables you to use your PC and serial communication protocol to control the projector. A commercially available RS232C cross cable is required to use this port. You can also control the pro- jector by using Dynamic Image Utility 2.0 included on the supplied
To do so you must first have Dynamic Image Utility 2.0 installed on your PC. If you are writing your own program, typical PC control codes are on page
12. PC CARD Slot 1/2
Insert a PC card, commercially available LAN card or NEC optional wireless LAN card here.
There are two slots: Slot 1 and Slot 2.
NOTE: A dummy card is inserted into each slot at the time of shipment. First remove the dummy cards before use.
13. PC CARD Eject Button 1/2
Press to eject a PC card partially. Each slot has its own eject button: 1 and 2.
