Manuals / NEC / Computer Equipment / Projector

NEC SX4000 user manual ISS-6020, Output to, Setting of S8601, Master, Slave

Models: SX4000

1 54

Download 54 pages 20.5 Kb

Page 27

Image 27

Set the DIP switch (S8601) of the Switcher as follows:

NOTE: Slave numbers 1 to 10 must correspond to the master’s slot numbers 1 to 10.

ISS-6020	Output to	Setting of S8601
ISS-6020G	Output to	Setting of S8601
ISS-6020G


								OPEN
Master	The Projector

			1		2		3		4		5		6		7		8
							SHORT


								OPEN
Slave 1	Slot 1 of the Master

			1		2		3		4		5		6		7		8
							SHORT


								OPEN
Slave 2	Slot 2 of the Master

			1		2		3		4		5		6		7		8
							SHORT


								OPEN
Slave 3	Slot 3 of the Master

			1		2		3		4		5		6		7		8
							SHORT


								OPEN
Slave 4	Slot 4 of the Master

		1		2		3		4		5		6		7		8
		1		2		3		4		5		6		7		8
							SHORT


								OPEN
Slave 5	Slot 5 of the Master

		1		2		3		4		5		6		7		8
		1		2		3		4		5		6		7		8
							SHORT


								OPEN
Slave 6	Slot 6 of the Master

		1		2		3		4		5		6		7		8
		1		2		3		4		5		6		7		8
							SHORT


								OPEN
Slave 7	Slot 7 of the Master

		1		2		3		4		5		6		7		8
		1		2		3		4		5		6		7		8
							SHORT


								OPEN
Slave 8	Slot 8 of the Master

		1		2		3		4		5		6		7		8
		1		2		3		4		5		6		7		8
							SHORT


								OPEN
Slave 9	Slot 9 of the Master
Slave 9	Slot 9 of the Master
			1		2		3		4		5		6		7		8
							SHORT


								OPEN
Slave 10	Slot 10 of the Master
Slave 10	Slot 10 of the Master

			1		2		3		4		5		6		7		8
							SHORT

E – 20

Page 27

Image 27

NEC SX4000 user manual ISS-6020, Output to, Setting of S8601, Master, Slave

Contents

User’s Manual Bedienungshandbuch MultiSync SX6000/SX4000User’s Manual MultiSync SX6000/SX4000High Light Output Projection System AVERTISSEMENT DOC compliance NoticeDOC avis de conformation 3. GSGV Acoustic Noise Information OrdinancePower Supply Important SafeguardsInstallation To Dealer or InstallerNettoyage Recommandations importantesInstallation AlimentationHOW YOU CAN GET WARRANTY SERVICE LIMITED WARRANTY USA and Canada onlyHOW LONG IS THE WARRANTY WHAT IS COVERED AND WHAT IS NOT COVEREDTABLE OF CONTENTS Whats In The Box? INTRODUCTIONIntroduction to the MultiSync SX6000/SX4000 Projector Getting StartedPress to the OFF position 0 to turn the main power off 1. Part Names and FunctionsRemote sensor ControlsNOTE This terminal accepts component signal only Terminal PanelNOTE This projector is compatible with the ISS-6020 Switcher for the ISS-6020 switcher11. RGB Digital Input/Output Connectors DVI-D 24 pin NOTE The Pixel Phase is not available Remote ControlRemote Control Battery Installation Remote Control PrecautionsScreen Size and Projection Distance 2. INSTALLATIONSetting Up Your Projector NOTE The lens must be installed by service personnel onlyCeiling/ Front Lens Shift Adjustable RangeMaximum Possible Range for TL-1Z/1ZH, TL-2Z and TL-4Z Fixed Lens TL-08SFRetracting the Handles Moving The ProjectorSelecting A Location Pulling Out the Handles2. Turn On The Projector Connecting the Power Cable and Turn on the Projector3. BASIC OPERATION Using the Power Cable StopperAbout Startup Screen TEST Set up the projector+ + + +2 Hookup Setting up for Double or Triple Stacking in Link ModeKeystone 1 Stacking the ProjectorsNOTE Use a different single color for each projector 6 Link Mode SettingNOTE In the Link mode the Lens Memory feature is not available 4 Display the internal crosshatch test patternDesktop Rear Projection Projector OrientationCeiling Front Projection Ceiling Rear ProjectionConnecting Your Document Camera When used in standalone operation4. CONNECTIONS Connecting Your PC Or Macintosh ComputerFor more details, contact your dealer When Used with One Switcher ISS-6020/ISS-6020GFor more details, contact your dealer When Used with Two or More Switchers 100 InputsHow to make connections Set the DIP switch S8601 of the SwitcherMaster Setting of S8601ISS-6020 Output toREMOTE 1 Connector Pin NoFUNCTION FUNCTION When used in stand alone operationPin No SHORT/OPENOperating Multiple Projectors with Remote Control Connecting a PC with RGB digital connector Using the RGB DIGITAL connectors SX6000 onlyConnection for Double or Triple Stacking in Link Mode Link ModeGeneral Controls 5. OPERATIONUsing The Menus One input is switched to anotherCustomizing Basic/Custom Menu NOTE This feature is available for SW 2 Level mode only A List of Direct Key Combinationsslot without displaying the Select Slot window Menu Tree When Switcher Control is turned onStand alone Page Menu windows or dialog boxes typically have the following elements Menu ElementsEntry List Menu Descriptions & Functions Source SelectNOTE Existing direct key settings are overwritten with new settings SwicherImage Adjust SourceWhite Balance PictureAspect Ratio not available for RGB Horizontal/Vertical Position when Auto Adjust is offResolution when Auto Adjust is off Video AdjOption Adj NOTE When connecting with a scan converterLens Memory Ref AdjSignal Type NOTE This feature is available on RGB 1 and 2 onlyturns to the factory preset Factory DefaultProjector Options TimerMenu Sleep TimerMenu Mode Date, Time PresetSignal Select VIDEO 1/2, S-VIDEO1/2 and Switcher SetupS-Video Mode Select Signal Select RGB1/2Contents HelpLink Mode Switcher ControlTest Pattern Source InformationProjector Information 6. SPECIFICATIONS OpticalElectrical Addressable Remote Control wired / wireless Mechanicalwith lens hood and foot X DIGITAL RGB BOARD 7. Optional AccessoriesXT SDI BOARD SX HDSDI BoardResolution H×V 8. Compatible Input Signal ListCompatible Input Signal List Signal NameMaster projector 9. List of Menu Items Available on Link ModeLink mode Function2.13 DimensionsAppendix 35.5Printed in Japan 7N8P0142

ISS-6020

Output to

Setting of S8601

Master

Slave 1