Manuals / NetComm / Computer Equipment / Network Router

NetComm NP725 manual 4.2 AP, Virtual AP Overview, Web Management Interface

Models: NP725

1 55

Download 55 pages 22.85 Kb

Page 28

Image 28

Chapter 4. Web Management Interface

4.2AP

This section provides information on the following functions: Overview, General, VAP Configuration, Security, Advanced and Access Control. The NP725 supports up to eight WLANs by Virtual Access Point (VAP). Each VAP can have its own settings including ESSID, VLAN ID, security settings, and etc. Therefore, these VAPs can bring different service level to clients depending on the ESSID connected to. Please click on the menu item AP to configure VAPs.

4.2.1 Virtual AP Overview

The overall status is collected in this page, including enable/disable state, security type, MAC ACL state, and advanced settings. NP725 has 8 VAPs; each has its own setting. In the table, please click on the specific item to have detailed configuration of these VAPs respectively.

State: The hyperlink showing enable or disable connects to the screen of VAP Configuration.

Page 28

Image 28

NetComm NP725 manual 4.2 AP, Virtual AP Overview, Web Management Interface

Contents

User Guide NP725 - Wireless Access PointNP725 User Guide Table of Contents ChapterChapter System Overview4.5.3 4.5.4Legal & Regulatory Information WDS List Status1.2 Product Features 1.1 OverviewChapter 1. Introduction Chapter 1. Introduction1.3 Deployment Topology Examples ƒ Three NP725s construct a network with wired and wireless segmentsƒ The AP-2 plays the role as a wireless bridge Chapter 1. Introduction2.1 Package Contents Chapter 2. System Overview2.2 Hardware Chapter 2. System Overviewƒ RESET Button Chapter 2. System OverviewRear Panel ƒ LAN 1 / LAN22.3 System Requirement and Preparation PreparationsChapter 2. System Overview Top Panel3.1 Wireless LAN Access Point Connection Chapter 3. InstallationChapter 3. Installation 3.2 Basic Configuration Chapter 3. InstallationChapter 3. Installation Change PasswordConfigure AP Settings Chapter 3. InstallationCheck VAP Profile Settings Chapter 3. Installation Check AP StatusChoose Security Type 1 Select AP menu 2 Select Security submenu to continueChapter 3. Installation ƒ Change Security Type to WEPChapter 3. Installation ƒ Change Security Type toChapter 3. Installation ƒ Change Security Type to WPA-PSKChapter 3. Installation ƒ Change Security Type to WPA-RadiusChapter 3. Installation Configure WDS SettingsConfigure the Peer Obtain WDS List StatusNow, the system has been installed and configured successfully Chapter 3. InstallationCongratulations Chapter 4. Web Management Interface Chapter 4. Web Management InterfaceIntroduction Chapter 4. Web Management InterfaceLog into Web Management Interface ƒ LoginChapter 4. Web Management Interface ƒ Logout4.1 System 4.1.1 System InformationChapter 4. Web Management Interface ƒ System Information¾ Synchronization There are two options of setting system time Chapter 4. Web Management Interface¾ Device Time Current system time ¾ Time Zone Take UTC offset to set this field1 NTP Enabled Chapter 4. Web Management Interface4.1.2 Network Settings Chapter 4. Web Management Interface4.1.3 Management Services Chapter 4. Web Management Interface4.2.1 Virtual AP Overview 4.2 APChapter 4. Web Management Interface ƒ Security Type The hyperlink showing security type connects to the screen of Security Settings Chapter 4. Web Management InterfaceChapter 4. Web Management Interface 4.2.2 General Settings PowerChapter 4. Web Management Interface Mode4.2.3 VAP Configuration Chapter 4. Web Management Interface4.2.4 Security Settings Chapter 4. Web Management Interfaceƒ WPA-PSK Provides shared key authentication and WPA data encryption ƒ 802.1X Provides RADIUS authentication and dynamic WEPChapter 4. Web Management Interface Chapter 4. Web Management Interface 4.2.5 Advanced Wireless Settings Chapter 4. Web Management Interface4.2.6 Access Control Settings ƒ DisableChapter 4. Web Management Interface ƒ Allow Listƒ Deny List Chapter 4. Web Management Interfaceƒ RADIUS ACL Chapter 4. Web Management Interface 4.3.1 WDS Link Overview 4.3 WDSChapter 4. Web Management Interface 4.3.2 WDS Link Settings Chapter 4. Web Management Interface4.4 Utilities 4.4.1 Change PasswordChapter 4. Web Management Interface 4.4.2 Configuration Save / Restore Chapter 4 Web Management Interface4.4.3 System Upgrade Chapter 4. Web Management Interface4.4.4 Reboot Chapter 4. Web Management Interface4.5.1 System Overview 4.5 StatusChapter 4. Web Management Interface RF Card BandChannel BSSID4.5.2 Associated Client Status Chapter 4. Web Management Interface4.5.3 WDS List Status Chapter 4. Web Management Interface4.5.4 Event Log Chapter 4. Web Management InterfaceChapter 4. Web Management Interface 4.6 Online HelpThe Help button is at the upper right corner of the display screen Customer Information 4.7Legal & Regulatory InformationChapter 4. Web Management Interface Chapter 4. Web Management Interface Product WarrantyGNU General Public License Limitations of Warranty Chapter 4. Web Management InterfaceProduct Warranty Technical SupportP 02 9424 2070 F 02 9424 DYNALINK NZ 224b Bush Road, Albany, Auckland, New Zealand