Misc Configuration, SIP Device | Netopia Network Adapater specification

User Guide

7.6Misc Configuration

The Misc Configuration pages configures system-level parameters. This has three sections: SIP Device, STUN Parameters and Codec Preference.

Figure 7-6 VOIP ATA Misc Configuration

SIP Device:

This section configures the following infomartion:

•Local SIP Port: Enter the local SIP Port number on which VOIP ATA should listen for the messages. The range is 1 to 65535. (Default port is 5060)

•Media Base Port: Enter the Media Base Port (also known as RTP port) number. This parameter provides the base value from the media (RTP) ports that are assigned for various lines and the different call-sessions that may exist within an end-point. Odd port values are not recommended. If an Odd Value is entered, the next higher even value is used as the Media Base Port. This is to conform to the RFC specifications. The range is 1 to 65500. (Default port is 5000)

STUN Parameters:

This section configures for the NAT Traversal technique support in VOIP ATA.

STUN:

User Guide

7-42

Image 42

Netopia Network Adapater manual Misc Configuration, SIP Device, Stun Parameters

Contents

Netopia Voip ATA User’sGuide Revision Status Tables Of Content Appendix a Glossary User Guide Introduction Setup & Configuration Main features Call Out & CallCall features Audio Codec Feature Your Voip ATA at a glance Ports and buttons12V DC LED description ETH Installing Your Voip ATA Adsl Connection DiagramTypical Voip ATA Connection Cable Connection Diagram 2below shows a Cable Modem+Router connection diagram For Company Network Connection Connection via Company Network Setting Up Your Voip ATA functionality via Access to Voip ATA’s GUIAccessing GUI Using Static IP User Guide Accessing GUI Using Hub/Switch Accessing GUI Using Hub/Switch User Guide Setup Mode Overall Status Network Selection Firmware Version Basic ModeOverall Status Registration Status WAN Connection Type Current Voice Call StatusVoice Call Status Descriptions WAN Statistic General Reset CountersTCP Status Discarded Packets System Log Clear LogSave Log Basic Configurations DNS Proxy DNS ConfigurationUser Configured Auto Discovered Save Configuration DNS Proxy SettingDNS Server Setting Host IP Save Settings / Reboot Save & RebootReboot Only Rebooting Modem Advanced Mode User Guide New Service Provider SIP Service ProviderService Provider List Registration Interval User Guide Registrar Port Authentication MethodService Provider Action Proxy Port User Profile List Voip ATA Login Account ConfigurationPassword New User Profile Login Action Submit Changes Alert Timeout Voip ATA Timer ConfigurationPredial Timeout Disconnect Timeout User Guide Call Fwd No Ans Timeout New Country Ringtone ConfigurationWorking Country Ring Parameters User Guide Alerting Tone Normal Dial ToneRingBack tone Recall Tone Submit Changes Misc Configuration SIP DeviceStun Parameters User Guide Force Keep Alive Stun ServerStun Port Keep Alive Period Address Book Configuration Address Book User Guide User Guide Admin Privilege Miscellaneous ConfigurationHttp Server Tftp Server Admin / Username Password ConfigurationFTP Server Sntp Client User Guide Reset to Default Restore Settings Firmware Update How to Firmware Update Uploading .DLF file Save / Reboot 13 Save / Reboot 15 Rebooting Modem Internet Calls VoIP Advanced Call Features Consultation HoldMaking Phone Calls Pstn Calls Attended Transfer 4 3-Way Conferencing How ToCall Waiting Call Forwarding Forward When Busy Forward UnconditionalForward On No Answer IP Dialing IP Address Canceling Call ForwardingCall Return Through Server Troubleshooting Problem Corrective Action Appendix a Glossary User Guide 10-63 User Guide 10-64 User Guide 10-65 Appendix B Dial Plan for Pulver B1 Basic Dial Plan B1.1 Pulver USA Dial PlanB1.2 Explanation of the Rules Descriptions User Guide 10-67 B2 Calling Other Service Provider Numbers through Pulver Service Provider Partner Recommended Dial Plan Rule User Guide 10-69