PROJECTING AN IMAGE (BASIC OPERATION)
This section describes how to turn on the projector and to project a pic- ture onto the screen.
Turning on the Projector
Before you turn on your projector, ensure that the computer or video source is turned on and that your lens shutter is open.
ZOOM
S |
|
|
|
|
|
|
|
|
FOCU |
|
|
|
|
|
|
|
|
| PUSH |
|
|
|
|
|
|
|
|
|
|
|
|
|
| PUTE | R |
|
|
|
|
|
| COM |
| |
|
|
|
|
|
|
|
| |
|
|
|
|
| VIDE | O IN |
|
|
|
|
|
|
|
|
|
| |
|
|
|
| EO | IN |
|
|
|
|
|
|
|
|
|
|
| |
|
| DIO | IN |
|
|
|
|
|
CLOSE | AU |
|
|
|
|
|
|
|
Only after you press the POWER (ON/STAND BY) button on the projec- tor cabinet or POWER ON button on the remote control for a minimum of 2 seconds will the power indicator turn to green and the projector be- come ready to use.
SEL | E | OFF | P0WER | ON |
CT | ||||
|
|
|
| COMPUTER |
MENU |
| VIDEO | COMP. | |
SOURCE | AUTO ADJ. |
|
| |
LAMP |
|
|
|
|
ENTER | AUTO |
| ASPECT | |
STATUS |
|
| ||
|
|
|
|
POWER
ON/STAND BY
ENTER
NOTE: To turn the projector on by plugging in the power cable, use the menu and enable the “Auto Start” feature. (See page
2. Press the ENTER button to execute the selection.
SE | L E | OFF | P0WER | ON |
CT | ||||
|
|
|
| COMPUTER |
MENU |
| VIDEO | COMP. | |
SOURCE | AUTO ADJ. |
|
| |
LAMP |
|
|
|
|
ENTER | AUTO |
| ASPECT | |
STATUS |
|
|
|
|
POWER |
|
|
|
|
ON/STAND BY |
|
|
|
|
|
|
| ENTER |
|
|
| MENU |
| CANCEL |
After this has been done, you can proceed to the menu operation.
NOTE: Immediately after turning on the projector, screen flicker may occur. This is not a malfunction. Wait 3 to 5 minutes until the lamp lighting is stabilized.
When the Lamp mode is set to Eco, the Lamp indicator will light green.
If one of the following things happens, the projector will not turn on.
*If the internal temperature of the projector is too high, the projector detects abnormal high temperature. In this condition the projector will not turn on to protect the internal system. If this happens, wait for the projector's internal components to cool down.
*When the lamp reaches its end of usable life, the projector will not turn on. If this happens, replace the lamp.
*If the lamp fails to light, and if the STATUS indicator flashes on and off in a cycle of six times, wait a full minute and then turn on the power.
If one of the following things happen, the projector will mute a picture. If it continues muting for 15 minutes, the projector will go into standby mode.
* Turning on the power with the lens shutter closed.
Note on Startup screen (Menu Language Select screen)
When you first turn on the projector, you will get the Startup screen. This screen gives you the opportunity to select one of the 7 menu languages.
NOTE: If you want, you can select one of the 20 menu language later. See "Lan- guage" on page
To select a menu language, follow these steps:
1.Use the dial to select one of the 7 languages for the menu.
When using the remote control, keep pressing the button several times until your language is highlighted.
| OFF | P0WER | ON |
| SELECT |
| COMPUTER |
|
|
| |
| VIDEO | COMP. | |
MENU | AUTO ADJ. |
|
|
| AUTO |
| ASPECT |
*Closing the lens shutter during operation.
*Directing the lens downward by more than 60° from level during operation.
*Turning on the power with the lens directed down by more than 60° from level.
LAMP
SOURCE
ENTER
STATUS
POWER
ENTER
ON/STAND BY
MENUCANCEL