Manuals / Norton Abrasives / Power Tools / Saw

Norton Abrasives C6126, C3120, C6120, C3126, C3130, C6136, C6130 Engine Group 31HP, Description

Models: C6120

1 90

Download 90 pages 19.25 Kb

Page 69

Engine Group 31HP

	ITEM	DESCRIPTION	PART No.	ITEM	DESCRIPTION	PART No.
	1	See INSTRUMENT PANEL Detail	-NA-		FUEL FILTER ELEMENT 31HP
	1	See INSTRUMENT PANEL Detail	-NA-	14	ONLY	237285
				14	ONLY	237285
	2	GROMMET	N1C0066	15	NUT 7/16-14 HEX HEAD	8143004
				15	NUT 7/16-14 HEX HEAD	8143004
	3	FUEL TANK CAP W/GAGE	237284	16	SCR 7/16-14 X 4 1/2 HEX HD CAP	8041086
				16
	4	FUEL TANK GROMMET	N1C0016	17	SCR 7/16-14 X 3 1/2 HEX HD CAP	8041082
				17
	5	FIT BARB HOSE 1/4FPTX5/16	9602006		ENG 31 HP DEUTZ D. F2L2011	236032
	5	FIT BARB HOSE 1/4FPTX5/16	9602006	18	Deutz Specification 7483	236032
				18	Deutz Specification 7483
	6	ELBOW 1/4MPT x 1/4FPT	9499001
	6	STREET BRASS	9499001	19	AIR FILTER ASSEMBLY 31HP	237281
		STREET BRASS		19	AIR FILTER ASSEMBLY 31HP	237281
	7	FUEL TANK	237204	20	AIR FILTER PRIMAERY 31HP	237282
	7	FUEL TANK	237204	20	ONLY	237282
					ONLY
	8	WASHER 5/16 SPING LOCK	8177011	21	MUFFLER COMPLETE 31 HP	237412

	9	WASHER 5/16 SAE	8172008	22	THROTTLE CABLE BRACKET	237336

	10	SCR 5/16-18 X 1 HEX HD CAP	8041028	23	CABLE THROTTLE LOCK 5'	237241

	11	SCR 1/2-20UNF X 1 HEX HEAD	8042095	24	SCR 3/8-16 X 1 1/4 HEX HD CAP	8041051
	11	CAP	8042095	24	SCR 3/8-16 X 1 1/4 HEX HD CAP	8041051
		CAP
	12	FUEL LINE 5/16ID X 1/2"OD X	237433	25	WASHER 3/8 SPRING LOCK	8177012
	12	25"L	237433	25	WASHER 3/8 SPRING LOCK	8177012
		25"L
	13	CLAMP HOSE WORM 3/8"TO 5/8"	227126	26	SCR 3/8-16 X 1 1/4 HEX HD CAP	8041051

69

Image 69

Norton Abrasives C6126, C3120, C6120, C3126, C3130, C6136, C6130 owner manual Engine Group 31HP, Description

Contents

MODELS C3120 C6120 C3126 C6126 C3130 C6130 C6136 Owners ManualLARGE CONCRETE SAWS MODEL SERIAL NO PURCHASE FROM ADDRESS CITY STATE ZIP TELEPHONE NO WARRANTYRead Owners Manual Before Use Table of ContentsCONTENTS III. MaintenanceI. PREPARATION A. Safety PrecautionsDO NOT LIFT THE SAW BY THE HANDLE BARS Important! The following safety precautions must always be observedEye Protection Dust and Silica WarningHearing RespiratoryA. Safety Precautions You Are Responsible For Your SafetyI. PREPARATION B. AssemblyDimensions/Weight C. C31xx Concrete Saw SpecificationsCharacteristics EngineDimensions/Weight C. C61xx Concrete Saw SpecificationsCharacteristics EngineRead and understand this manual before running or using the machine A. Installing the BladeII. OPERATION Blade Shaft Installation Changing the Blade Side B. Aligning the Pointer For The Best Performance Only Use Norton Diamond BladesMultiple Mounted Blades DescriptionFront Pointer Assembly Never use a gasoline or an oil and gasoline mixture C. Controls and Functions4. Controls/Gauges Location of Controls and GaugesControl and Gauge locations and function Chart TypeFunction Function Type5. Starting the Engine Eye ProtectionStraight Drive 31 & 61 HP D. Water Supply E. Operating the SawJackshaft Drive 61HP Hearing Eye ProtectionRespiratory Head ProtectionJackshaft Drive 61HP Straight Drive 31 & 61 HPTransmission While The Machine Is In The Forward Or Reverse Positions Caution Do Not Engage Or Disengage TheF. Cutting Technique Depth GaugeDepth Gauge Depth Gauge and Depth Lock Locations Depth LockStep Cutting Additional Guide Lines for Sawing F. Lead Off Adjustment Page A Engine III. MaintenanceEye Protection HearingDeutz Engine Components ‡ Locations of Engine ComponentsOil Filler Neck and Dipstick Locations ‡ Oil Checking the Oil ‡Oil Quality Grade Oil SpecificationsApproved Oils DeutzOil Change intervals ‡ Fuel SpecificationsLube Oil Grade Deutz Lube Oil Quality ClassWinter Fuel Grades Fault Engine ServiceMeasures CauseB. Air Filter Assembly Air Filter C31xx Dry Cutting Engine MaintenanceAir Filter C61xx Temperature C. BearingsBearing Location Shaft Sizeengine is running D. V Belts Warning Never make adjustments to belts or pulleys whileE. Hydraulic Raise/Lower System 3. Remember too much tension shortens belt and bearing lifeAdjusting Screw 2. Locate the Check Valve Adjusting Screw as shown below Check Valve1. Remove the Hydraulic Pump Cover from the console 4. Replace the Hydraulic Pump CoverHydraulic Pump Maintenance Symptom 8. Monarch Hydraulic Pump Symptom /CauseMotor Start Solenoid Switch Electrical Switch Open Circuit Motord. Volt Meter c. Continuity Lighte. OHM Meter 10. Hydraulic Fluid a. The Purpose of Oil1. Fluid must be compatible with Buna N sealing compounds 11. Hydraulic Pump Priming A. New Installations5. The viscosity index should be as high as possible A. Viscosity SUS 185 to 205 @ 100OF Viscosity SUS 45 to 50 @ 210OF12. Hydraulic Pump Electrical Problems 3. A loose or improperly installed suction hose or pick up tube2. Partially clogged suction filter 4. A bad front pump seal4. Ground cable size not equivalent or larger than battery cable C. Cause for Low Voltage 1. Battery capacity too small6. Burnt contacts on motor solenoid or start switch 1. Remove head assembly from motorF. Electrical Switches 3. Place a few drops of oil on felt liner in head assembly1. Use”continuity light to test switch. See Test Equipment Section 4. Check brush set for wear and replace if necessaryG. Motor Start Solenoid Switches The three post solenoid switch is wired and constructed as followsH. Shorts, Ground Faults and Open Circuits A. Relief valve pressure too high 1. Symptoms 12. Diagnosing and Repairing Hydraulic Pump Relief ValvesAmp draw and battery drain excessive when system is dead headed 2. Repair Procedure13. Diagnosing and Repairing Hydraulic Pump Relief Valves B. Relief Valve Pressure Too Low 1. SymptomsThe adjusting screw has backed up Motor RPM is faster than normal Cylinder will not extendF. Transmission G. Self-Propelling Operations Recommended Fluids For Eaton Model 6 Transmissions7. 20W Straight Viscosity SE, CC, or CD Rated Engine Oil 2. Transmission Engage/Disengage Lever 1. Speed Control LeverToo Move the Machine 3. Transmission MaintenanceH. Electrical System Wiring Section “A” Accessory/Switches Wiring Section “B” Controls/Instruments BLACK Wiring Section “C” Wiring Harness ConnectorBROWN YELLOWBLUE/BLACK Wiring Section “D” EngineRED/BLACK BROWNA. Ordering Information IV. PARTS LIST SECTIONDescription Part NumberStraight Drive Non-Jackshaft Models Only B Blade Guard Conversion ChartC Service Parts Main Frame Group 31HP and 61HP Main Frame Group 31HP and 61HP DESCRIPTIONDESCRIPTION SHAFT COVER 61 HP Main Frame Group 31HP and 61HPEngine Group 61HP Engine Group 61HP DESCRIPTIONDESCRIPTION Engine Group 31HP Engine Group 31HP DESCRIPTIONDESCRIPTION Stub Shaft Group 31HP and 61HP Sold Individually Stub Shaft Group 31HP and 61HPSold Individually 31HP 12 requiredInstrument Panel Group 31HP and 61HP Instrument Panel Group 31HP and 61HP DESCRIPTIONDESCRIPTION Transmission and Rear Axle Group 31HP and 61HP Transmission and Rear Axle Group 31HP and 61HP DESCRIPTIONDESCRIPTION Transmission and Rear Axle Group Depth Stop and Front Axle Group 31HP and 61HP Depth Stop and Front Axle Group 31HP and 61HP DESCRIPTIONDESCRIPTION Controls and Lever Group Controls and Lever Group DESCRIPTIONDESCRIPTION Electro-Hydraulic Group 31HP and 61HP Electro-Hydraulic Group DESCRIPTIONDESCRIPTION Blade Shaft Group Non-Jackshaft 31HP and 61HP Blade Shaft Group Non-Jackshaft Blade Guard Group Blade Guard Group 31HP and 61HP DESCRIPTIONDESCRIPTION Water Control System Group DESCRIPTIONDESCRIPTION To Water System Optional Water Pump GroupExploded View Assembled ViewNOTE Water Pump Kit 237243 items# 1, 2, 3, 4, 5, 6, 8, 9, 10 are includes all Optional Water Pump Group2270 West Washington Street Stephenville, TX Phone Saint-Gobain Abrasives, Inc