Manuals / Norton Abrasives / Power Tools / Saw

Norton Abrasives C6130, C3120, C6120, C3126, C3130, C6136, C6126 Electro-Hydraulic Group, Description

Models: C6120

1 90

Page 82

Electro-Hydraulic Group

ITEM	DESCRIPTION	PART No.	ITEM	DESCRIPTION	PART No.
1	HYDRAULIC PUMP (FLUID:	149001	12	HYD FITTING 1/4	N1D0006
1	USE ATF DEXTRON B)	149001	12	HYD FITTING 1/4	N1D0006
	USE ATF DEXTRON B)
2	BREATHER CAP 3/4MPT	237269	13	FLOW CONTROL VALVE	N1C0079

3	SOLINOID VALVE	N1C0182	14	ELBOW	N1D0007

4	SOLINOID MAGNET	N1C0181	15	HYDRAULIC HOSE ASSY.	N1C0093

5	NUT	N1D0110	16	RAISE / LOWER SWITCH	N1C0088

6	CABLE ASSY	N1C0183	17	SWITCH HANDLE	N1E0265

7	FLATWASHER 1/4"	N1D0111	18	NUT 3/4-10 JAM	N1D0288

8	BOLT 1/4-20 x 1/2	N1D0049	19	WIRE ASSY	N1C0089

9	SOLINOID (MOTOR)	N1C0184	31	SWITCH HANDLE	N1E0265

10	BATTERY CABLE	N1C0034	32	NUT 7/8-9 HEX JAM	8150009

11	HYD FITTING/RING	N1D0001

Page 82

Image 82

Norton Abrasives C6130, C3120, C6120, C3126, C3130, C6136, C6126 owner manual Electro-Hydraulic Group, Description

Contents

Owners Manual MODELS C3120 C6120 C3126 C6126 C3130 C6130 C6136LARGE CONCRETE SAWS WARRANTY MODEL SERIAL NO PURCHASE FROM ADDRESS CITY STATE ZIP TELEPHONE NOCONTENTS Table of ContentsRead Owners Manual Before Use III. MaintenanceDO NOT LIFT THE SAW BY THE HANDLE BARS A. Safety PrecautionsI. PREPARATION Important! The following safety precautions must always be observedHearing Dust and Silica WarningEye Protection RespiratoryYou Are Responsible For Your Safety A. Safety PrecautionsB. Assembly I. PREPARATIONCharacteristics C. C31xx Concrete Saw SpecificationsDimensions/Weight EngineCharacteristics C. C61xx Concrete Saw SpecificationsDimensions/Weight EngineA. Installing the Blade Read and understand this manual before running or using the machineII. OPERATION Blade Shaft Installation Changing the Blade Side Multiple Mounted Blades For The Best Performance Only Use Norton Diamond BladesB. Aligning the Pointer DescriptionFront Pointer Assembly 4. Controls/Gauges C. Controls and FunctionsNever use a gasoline or an oil and gasoline mixture Location of Controls and GaugesType Control and Gauge locations and function ChartFunction 5. Starting the Engine TypeFunction Eye ProtectionStraight Drive 31 & 61 HP E. Operating the Saw D. Water SupplyJackshaft Drive 61HP Respiratory Eye ProtectionHearing Head ProtectionStraight Drive 31 & 61 HP Jackshaft Drive 61HPCaution Do Not Engage Or Disengage The Transmission While The Machine Is In The Forward Or Reverse PositionsDepth Gauge F. Cutting TechniqueDepth Gauge Depth Lock Depth Gauge and Depth Lock LocationsStep Cutting Additional Guide Lines for Sawing F. Lead Off Adjustment Page Eye Protection III. MaintenanceA Engine HearingLocations of Engine Components Deutz Engine Components ‡Oil Checking the Oil ‡ Oil Filler Neck and Dipstick Locations ‡Approved Oils Oil SpecificationsOil Quality Grade DeutzLube Oil Grade Fuel SpecificationsOil Change intervals ‡ Deutz Lube Oil Quality ClassWinter Fuel Grades Measures Engine ServiceFault CauseB. Air Filter Assembly Dry Cutting Engine Maintenance Air Filter C31xxAir Filter C61xx Bearing Location C. BearingsTemperature Shaft SizeE. Hydraulic Raise/Lower System D. V Belts Warning Never make adjustments to belts or pulleys whileengine is running 3. Remember too much tension shortens belt and bearing life1. Remove the Hydraulic Pump Cover from the console 2. Locate the Check Valve Adjusting Screw as shown below Check ValveAdjusting Screw 4. Replace the Hydraulic Pump CoverHydraulic Pump Maintenance Motor Start Solenoid Switch 8. Monarch Hydraulic Pump Symptom /CauseSymptom Electrical Switch Open Circuit Motore. OHM Meter c. Continuity Lightd. Volt Meter 10. Hydraulic Fluid a. The Purpose of Oil5. The viscosity index should be as high as possible 11. Hydraulic Pump Priming A. New Installations1. Fluid must be compatible with Buna N sealing compounds A. Viscosity SUS 185 to 205 @ 100OF Viscosity SUS 45 to 50 @ 210OF2. Partially clogged suction filter 3. A loose or improperly installed suction hose or pick up tube12. Hydraulic Pump Electrical Problems 4. A bad front pump seal6. Burnt contacts on motor solenoid or start switch C. Cause for Low Voltage 1. Battery capacity too small4. Ground cable size not equivalent or larger than battery cable 1. Remove head assembly from motor1. Use”continuity light to test switch. See Test Equipment Section 3. Place a few drops of oil on felt liner in head assemblyF. Electrical Switches 4. Check brush set for wear and replace if necessaryThe three post solenoid switch is wired and constructed as follows G. Motor Start Solenoid SwitchesH. Shorts, Ground Faults and Open Circuits Amp draw and battery drain excessive when system is dead headed 12. Diagnosing and Repairing Hydraulic Pump Relief ValvesA. Relief valve pressure too high 1. Symptoms 2. Repair ProcedureThe adjusting screw has backed up B. Relief Valve Pressure Too Low 1. Symptoms13. Diagnosing and Repairing Hydraulic Pump Relief Valves Motor RPM is faster than normal Cylinder will not extendF. Transmission Recommended Fluids For Eaton Model 6 Transmissions G. Self-Propelling Operations7. 20W Straight Viscosity SE, CC, or CD Rated Engine Oil 1. Speed Control Lever 2. Transmission Engage/Disengage Lever3. Transmission Maintenance Too Move the MachineH. Electrical System Wiring Section “A” Accessory/Switches Wiring Section “B” Controls/Instruments BROWN Wiring Section “C” Wiring Harness ConnectorBLACK YELLOWRED/BLACK Wiring Section “D” EngineBLUE/BLACK BROWNDescription IV. PARTS LIST SECTIONA. Ordering Information Part NumberB Blade Guard Conversion Chart Straight Drive Non-Jackshaft Models OnlyC Service Parts Main Frame Group 31HP and 61HP DESCRIPTION Main Frame Group 31HP and 61HPDESCRIPTION Main Frame Group 31HP and 61HP SHAFT COVER 61 HPEngine Group 61HP DESCRIPTION Engine Group 61HPDESCRIPTION Engine Group 31HP DESCRIPTION Engine Group 31HPDESCRIPTION Stub Shaft Group 31HP and 61HP Sold Individually Stub Shaft Group 31HP and 61HPSold Individually 31HP 12 requiredInstrument Panel Group 31HP and 61HP DESCRIPTION Instrument Panel Group 31HP and 61HPDESCRIPTION Transmission and Rear Axle Group 31HP and 61HP DESCRIPTION Transmission and Rear Axle Group 31HP and 61HPDESCRIPTION Transmission and Rear Axle Group Depth Stop and Front Axle Group 31HP and 61HP DESCRIPTION Depth Stop and Front Axle Group 31HP and 61HPDESCRIPTION Controls and Lever Group DESCRIPTION Controls and Lever GroupDESCRIPTION Electro-Hydraulic Group 31HP and 61HP DESCRIPTION Electro-Hydraulic GroupDESCRIPTION Blade Shaft Group Non-Jackshaft 31HP and 61HP Blade Shaft Group Non-Jackshaft Blade Guard Group DESCRIPTION Blade Guard Group 31HP and 61HPDESCRIPTION DESCRIPTION Water Control System GroupDESCRIPTION Exploded View Optional Water Pump GroupTo Water System Assembled ViewOptional Water Pump Group NOTE Water Pump Kit 237243 items# 1, 2, 3, 4, 5, 6, 8, 9, 10 are includes allSaint-Gobain Abrasives, Inc 2270 West Washington Street Stephenville, TX Phone