HT-R518_En.book Page 54 Tuesday, March 11, 2008 11:31 AM

Recording

This section explains how to record the input source and how to record audio and video from separate sources.

Notes:

The surround sound and DSP listening modes cannot be recorded.

Copy-protected DVDs cannot be recorded.

Sources connected to the analog multichannel input cannot be recorded.

Sources connected to a digital input cannot be recorded. Only analog inputs can be recorded.

DTS signals will be recorded as noise, so don’t attempt analog recording of DTS CDs or LDs.

While the Pure Audio listening mode is selected, the VCR/DVR OUT V and S jacks don’t output video sig- nals, so select another mode when recording.

Recording the Input Source

Audio sources can be recorded to a recorder (e.g., cas- sette deck, CDR, MD) connected to the TAPE OUT jack. Video sources can be recorded to a video recorder (e.g., VCR, DVR) connected to the VCR/DVR OUT jacks. See pages 18 to 32 for hookup information.

Recording from Different AV Sources

You can overdub audio onto your video recordings by simultaneously recording audio and video from two sep- arate sources. This is possible because only the audio source is switched when an audio-only input source, such as TAPE, TUNER, or CD, is selected, the video source remains the same.

In the following example, audio from the CD player con- nected to the CD IN and video from the camcorder con- nected to the AUX INPUT VIDEO jack are recorded by the VCR connected to the VCR/DVR OUT jacks.

AUX INPUT

VIDEO

L AUDIO R

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Camcorder

video signal audio signal

HDMI

IN 3

IN 2

ASSIGNABLE

 

 

IN 1

OUT

1

DVD VCR/DVR CBL/SAT

AUX TAPE TUNER

CD

Remote

Use the input selector buttons to select the source that you want to record.

See “Which Connections Should I Use?” on page 19 to see which signals can be output and recorded.

You can watch the source while record- ing it. The AV receiver’s MASTER

DIGITAL IN

COMPONENT VIDEO

 

Y

1

 

(DVD)

 

COAXIAL

CB/ PB

 

2

 

(CBL/SAT)

 

 

CR/ PR

1

 

(VCR/DVR)

 

OPTICAL

IN 2 IN 1(DVD) OUT

 

2

ASSIGNABLE

 

 

 

 

 

(CD)

IN

OUT

IN

 

ASSIGNABLE

 

 

 

 

L

 

 

R

REMOTE

CONTROL

CDTAPE

CBL/SAT VCR/DVR

V

S

IN OUT IN

IN

OUT

IN

L

 

 

R

CBL/SAT VCR/DVR

 

AM

DVD

MONITOR

OUT

 

V

 

ANTENNA

 

FM

 

75

 

S

IN

 

FRONT

SURR CENTER

 

L

 

R

 

SUB

 

WOOFER

 

DVD

controller

VOLUME control has no effect on recording.

CD playerVCR

2

On your recorder, start record-

 

 

ing.

 

 

3

On the source component, start

 

 

playback.

 

 

Note:

If you select a different input source during recording, that input source will be recorded instead.

1

Prepare the camcorder and CD player for

 

playback.

 

 

2

Prepare the VCR for recording.

 

 

3

Press the [AUX] input selector button.

 

 

4

Press the [CD] input selector button.

 

This selects the CD player as the audio source but

 

leaves the camcorder as the video source.

 

 

5

Start recording on the VCR, then start

 

playback on the camcorder and CD player.

Video from the camcorder and audio from the CD player are recorded by the VCR.

54

Page 54
Image 54
Onkyo HT-R518 instruction manual Recording the Input Source, Recording from Different AV Sources