Onkyo SR804 Checking the Results, Use the Up and Down, Buttons to select the item that

First Time Setup—Continued

■Checking the Results

If you selected “Check the Results” in step 4 on the pre- vious page, the following menu appears and you can check the results of the automatic speaker setup.

Auto Speaker Setup

========================

1.Warning 2.Speaker Config 3.Speaker Distance 4.Speaker Level Adjust 5.Equalizer Settings

1.Warning—Undetected speakers and position warn- ings (see the right column).

2.Speaker Config—Connected speakers and crossover frequencies.

3.Speaker Distance—Distance from each speaker to the listening position.

4.Speaker Level Adjust—Optimum volume level for each speaker.

5.Equalizer Settings—Optimum equalizer settings for each speaker.

	Use the Up and Down [ ]/[ ]
	buttons to select the item that
ENTER	you want to check, and then
	press [ENTER].
	Press the [RETURN] button to return to
	the previous menu.
ENTER	1.Warning
	========================
	Not Detect:
	Distance Error:
	2.Speaker Config
	========================
	Subwoofer	:No
	Front	:80Hz(THX)
	Center	:80Hz(THX)
	Surround :80Hz(THX)
	SurrBack :80Hz(THX)
	SurrBack ch :2ch
	3.Speaker Distance
	========================
	Left		:12ft
	Center		:12ft
	Right		:12ft
	Surround R		: 7ft
	SurrBack		: 7ft
	Surround L		: 7ft
	Subwoofer		:12ft
	4.Speaker Level Adjust
	========================
	Left		: 0dB
	Center		: 0dB
	Right		: 0dB
	Surround R		: 0dB
	SurrBack		: 0dB
	Surround L		: 0dB
	Subwoofer		: 0dB
	5.Equalizer Setting
	========================
		Channel: Left
	========================
		80Hz	: 0dB
		250Hz	: 0dB
		800Hz	: 0dB
		2.5kHz	: 0dB
		8kHz	: 0dB

When you’ve finished checking, press the [RETURN] button to return to the menu in step 4.

Auto Speaker Setup

========================

Apply the Results

Check the Results

Retry

Retry with

Test noise Level up

Cancel

Warning Messages

In the warning messages, abbreviations are used to iden- tify the speakers (e.g., “L” for left, “R” for right, and so on).

Not Detect:

The speaker was not detected. Make sure that it’s connected properly.

Distance Error:

The speaker is either too close or too far away, or the distance could not be measured. Reposition the speaker.

Changing the Speaker Settings Manually:

In some situations, the measurements taken by the auto- matic speaker setup may not provide usable results. If running the speaker setup a second time still doesn’t pro- vide usable results, you’ll have to set the speaker settings yourself (see pages 70–75).

Please note that any THX main speakers should be set to 80 Hz (THX). If you set up your speakers using Auto- matic Speaker Setup, please make sure manually that any THX speakers are set to 80 Hz (THX) in the Speaker Configuration setting (see pages 70, 71).

Sometimes due to the electrical complexities of sub- woofers and the interaction with the room, THX recom- mends setting the level and the distance of the subwoofer manually.

Using a Powered Subwoofer:

If you’re using a powered subwoofer, because it’s posi- tioned low down on the floor and outputting very low frequency sounds, its output may not be detected prop- erly. If the subwoofer (abbreviation “SW”) appears on the Warning screen under Not Detect, turn up the sub- woofer’s volume and run the automatic speaker setup again. If the subwoofer has a built-in crossover, set it to the highest crossover frequency. If it has an LPF filter switch, set it to off or direct. Refer to your subwoofer’s instruction manual for details.

42