Onkyo SR804 Advanced Setup, Speaker Configuration, The Speaker Setup menu appears, nected

Advanced Setup

Speaker Setup

This section explains how to check the speaker settings and how to set them manually, which is useful if you change a speaker after performing the automatic speaker setup.

Some speaker settings are set automatically by the Auto- matic Speaker Setup function (see page 40).

2		Use the Up and Down [ ]/[ ]
		buttons to select “3. Speaker
		Setup,” and then press [ENTER].
	ENTER	The Speaker Setup menu appears.

ENTER

	V4	MULTI CH	DVD		TV CH
	4	5	6		-
	CD	TAPE	TUNER
	7	8	9
	PHONO				TV VOL
	+10	0	CLEAR
	- - / - - - 10	11		12
	INPUT SELECTOR
		MACRO
	1	2	3		ZONE2
RECEIVER		REMOTE MODE
	RECEIVER	DVD	CD		HDD
	TAPE/AMP
	TV	VCR	CABLE		SAT
			CDR		MD
	DIMMER				SLEEP
		U	ME
		MEN		NU
		OP
		T
ENTER	+
	CH	ENTER			VOL
	DISC
	ALBUM
	-
	PREV	RE		P	SETUP
	CH	TURN	SETU
	DISPLAY				MUTING
	REC	PLAYLIST			RANDOM
		LISTENING MODE

3

ENTER

ENTER

Use the Up and Down []/[ ] buttons to select “Speaker Con- figuration,” and then press [ENTER].

The Speaker Config menu appears.

3-2.Speaker Config

------------------------

a.Subwoofer		:Yes
b.Front	:80Hz(THX)
c.Center	:80Hz(THX)
d.Surround	:80Hz(THX)
e.SurrBack	:80Hz(THX)
f.SurrBack Ch		:2ch
g.LPF of LFE
	:80Hz(THX)
h.Subwoofer Mode
:-------------

STEREO	SURR
REPEAT	AUDIO	SUBTITLE	PLAY MODE
PURE A	DIRECT	THX	ALLST

Speaker Configuration

These settings are set automatically by the Automatic Speaker Setup function (see page 40).

With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. The following crossover frequencies can be specified: Full Band, 40 Hz, 60 Hz, 70 Hz, 80 Hz (THX), 90 Hz, 100 Hz, 120 Hz, 150 Hz, 200 Hz.

Specify Full Band for speakers that can output low-fre- quency bass sounds adequately, for example, speakers with a good sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover fre- quency will be output by the subwoofer instead of the speaker. Refer to your speakers’ manuals to determine the optimum crossover frequencies.

If you’re using THX-certified speakers, specify 80 Hz (THX) for all speakers.

1	Press the [RECEIVER] REMOTE
	RECEIVER

MODE button, followed by the [SETUP] button.

The main menu appears onscreen.

4		Use the Up and Down [			]/[	]
		buttons to select “a. Subwoofer,”
	ENTER	and then use the Left and Right
		[	]/[	] buttons to select:
			Yes: Select if a subwoofer is con-
				nected.
			No: Select if no subwoofer is con-
5				nected.
		Use the Up and Down [			]/[	]
		buttons to select “b. Front,” and
	ENTER	then use the Left and Right
		[	]/[	] buttons to select a

crossover frequency.

Note:

•If the Subwoofer setting in step 4 is set to No, this is fixed at Full Band.

6	Use the Up and Down [ ]/[ ]
	buttons to select “c. Center,” and
	then use the Left and Right
	ENTER
	[ ]/[ ] buttons to select a
	crossover frequency.
	If no center speaker is connected, select
	None.

Note:

•If the Front setting in step 5 is set to anything other than Full Band, Full Band cannot be selected here.

70