Onkyo SR805 instruction manual First Time Setup, Speaker Settings

First Time Setup

This section explains the settings that you need to make before using the AV receiver for the very first time.

Speaker Settings

	GAME/TV	AUX1				AUX2				TV CH
	4		5			6				-
If you change these settings,							you must run the auto-
	TAPE	TUNER				CD
matic speaker setup again (see page 55).
	7		8			9
	PHONO					D. TUN				TV VOL
	+10		0			CLEAR
	--/--- 10				11				12
	INPUT SELECTOR
		MACRO
	1		2			3				ZONE3
		REMOTE MODE
	DVD	VCR				CD				ZONE2
						CDR/MD					1
	TV	CABLE				DOCK				RECEIVER
		SAT								TAPE/AMP
	DIMMER									SLEEP
2, 3				EN		ME					2–5
		PM			U		N	U
		O
		T
	+
	CH				ENTER					VOL
	DISC
	ALBUM
1, 6	-	G
				UIDE		IT
	PREV					EX
		SE	T	UP		RE			N
	CH					TU
	DISPLAY									MUTING
	REC			PLAYLIST						RANDOM

If the impedance of any speaker is 4 ohms or more but less than 6, set the Speaker Impedance to 4 ohms.

If you’ve connected your front speakers to the FRONT and SURR BACK terminal posts for bi-amping or bridging (TX-SR875 only), you must change the Speaker Type setting. For hookup information, see “Bi- amping the Front Speakers” on page 23, or “Bridging the Front Speakers (TX-SR875 only)” on page 24.

Notes:

• When bridging is used, the AV receiver is able to drive up to 2.1 speakers in the main room.

• When bi-amping is used, the AV receiver is able to drive up to 5.1 speakers in the main room.

• Before you change these settings, turn down the vol- ume.

1	Press the [RECEIVER] button,
RECEIVER	followed by the [SETUP] button.
	The main menu appears onscreen.
S
E
T
UP
2	Use the Up and Down [ ]/[ ]
	buttons to select “2. Speaker
ENTER	Setup,” and then press [ENTER].
	The Speaker Setup menu appears.

ENTER

3	Use the Up and Down [	]/[ ]
	buttons to select “1. Speaker Set-
	tings,” and then press [ENTER].
	ENTER
	The Speaker Settings menu appears.
	2-1.Speaker Settings
	Speaker Impedance	6ohms
	Speakers Type	Normal
	ENTER

4	Use the Up and Down [ ]/[ ]
	buttons to select “Speaker

Impedance,” and use the Left and

ENTER

Right []/[ ] buttons to select:

4 ohms: Select if the impedance of any speaker is 4 ohms or more but less than 6.

6 ohms: Select if the impedances of all speakers are between 6 and 16 ohms.

5	Use the Up and Down [ ]/[ ]
	buttons to select “Speaker Type,”

and use the Left and Right

ENTER

[]/[ ] buttons to select:

Normal: Select this if you’ve con- nected your front speakers normally.

Bi-Amp:Select this if you’ve con- nected your front speakers for bi-amped operation.

BTL: (TX-SR875 only) Select this if you’ve connected your front speakers for bridged operation. The BTL indicator will appear on the display.

6		Press the [SETUP] button.
	S	Setup closes.
	E
	T
	UP

Notes:

•This procedure can also be performed on the AV receiver by using its [SETUP], [ENTER], and arrow buttons.

•The design of the TX-SR805 and TX-SR875 onscreen setup menus is slightly different. The TX-SR805 onscreen setup menus are used throughout this

instruction manual.

45