Onkyo TX-NR1010 instruction manual En-63, Speaker Setup, Digital Audio Input, Speaker Settings

Digital Audio Input

If you connect a component to a digital audio input, you must assign that input to an input selector. For example, if you connect your CD player to the OPTICAL IN 1, you must assign “OPTICAL1” to the “TV/CD” input selector. Here are the default assignments.

Input selector	Default assignment
BD/DVD	COAXIAL1
CBL/SAT	COAXIAL2
STB/DVR	COAXIAL3
GAME1	OPTICAL1
GAME2	- - - - -
PC	- - - - -
AUX	FRONT (Fixed)
TV/CD	OPTICAL2
PHONO	- - - - -

■BD/DVD, CBL/SAT, STB/DVR, GAME1, GAME2, PC, TV/CD, PHONO

`COAXIAL1, COAXIAL2, COAXIAL3, OPTICAL1, OPTICAL2:

Select the input to which the component has been connected.

`- - - - -:

Select if the component is connected to an analog audio input.

Note

•When an HDMI IN is assigned to an input selector in

“HDMI Input” (➔ page 61), the same HDMI IN will be set as a priority in this assignment. In this case, if you want to use the coaxial or optical audio input, make the appropriate selection in the “Audio Selector” (➔ page 77).

•Supported sampling rates for PCM signals (stereo/mono) from a digital input (optical and coaxial) are 32/44.1/48/88.2/96 kHz/16, 20, 24 bit.

•“AUX” is used only for input from the front panel.

Speaker Setup

1 2 3 4 “Setup” 5

Main Menu Speaker Setup

Some of the settings in this section are set automatically by Audyssey MultEQ® XT32 Room Correction and Speaker Setup (➔ page 39).

Here you can check the settings made by

Audyssey MultEQ XT32 Room Correction and Speaker Setup function, or set them manually, which is useful if you change one of the connected speakers after using Audyssey MultEQ XT32 Room Correction and Speaker Setup function.

Note

•These settings are not available in either of the following cases:

–a pair of headphones is connected.

–the “Audio TV Out” setting is set to “On” (➔ page 80).

–“HDMI Control(RIHD)” is set to “On” (➔ page 79) and you’re listening through your TV speakers.

Speaker Settings

If you change these settings, you must run Audyssey MultEQ XT32 Room Correction and Speaker Setup again (➔ page 39).

If the impedance of any speaker is 4 ohms or more but less than 6, set the minimum speaker impedance to 4 ohms.

If you bi-amp the front speakers, you must change the “Speakers Type(Front)” setting. For details on speaker wire connection, see “Bi-amping the Front Speakers” (➔ page 16). When connecting speakers without crossover network, you need to change the “Speakers Type(Front)” setting beforehand. For details on

Advanced Operations

connection, refer to “Using Speakers Without Crossover Network” (➔ page 16).

Note

•When bi-amping is used, the AV receiver is able to drive up to 5.2 speakers in the main room.

•Before you change these settings, turn down the volume.

■Speaker Impedance

`4ohms:

Select if the impedance of any speaker is 4 ohms or more but less than 6.

`6ohms:

Select if the impedances of all speakers are between 6 and 16 ohms.

■Speakers Type(Front)

`Normal:

Select this if you’ve connected your front speakers normally.

`Bi-Amp:

Select this if you’ve bi-amped your front speakers.

`Digital Crossover:

Select this if you’re using speakers without crossover network.

Tip

•If “Speakers Type(Front)” is set to “Digital Crossover”, a confirmation screen appears. Select “Next (2-7. Digital Processing Crossover Network)” to display the screen for Digital Processing Crossover Network (➔ page 67). Continue with the settings.

■Powered Zone 2, Powered Zone 3

`No

`Yes:

Zone 2/3 speakers can be used. (Powered Zone 2/3 enabled).

En-63