Manuals / Optiview / Photography / Security Camera

Optiview TRKPTZ -26NX, TRKPTZ-18NX user manual Auto Zooming Tracking Dome Camera User Manual

Models: TRKPTZ -26NX

1 53

Download 53 pages 12.57 Kb

Page 15

Image 15

Auto Zooming Tracking Dome Camera User Manual

manual. Please refer to the installation packet supplied with the back box for installation instructions.

After installed properly, power up the camera. It will start a configuration sequence. After the configuration is done, the monitor will display as below.

PTOL：PELCO-D

COMM：2400,N,8,1

ADDR：0

This information will remain on the monitor until dome operation begins.

Please refer to the following pages for more about how to operate and program the camera.

Access main menu (preset 95): Please refer to the Accessing Main Menu (Preset 95) section.

(1)Move joystick to position the cursor beside menu selection.

(2)Move the joystick up or down to submenu/cursor selections.

(3)Press iris Open to confirm selection.

(4)Press iris Close to cancel selection.

(5)Below instructions are based on using control keyboard as control device.

Page 15

Image 15

Optiview TRKPTZ -26NX, TRKPTZ-18NX Auto Zooming Tracking Dome Camera User Manual, PTOL：PELCO-D COMM：2400,N,8,1 ADDR：0

Contents

User Manual Auto Zooming TrackingDome Cameras Contents 3.8 Other Functions 3.7 Dome LabelSection1 Instruction 1.1 Production Introducing1.2 Character 1.3 Function Description Page  Targets are in near and far at the same time Auto Zooming Tracking Dome Camera User ManualThe camera will not auto focus in the following status  Target is not in the center of image14 Random Scan 17 Alarms Alarms input 1.4 Specification Comparison Chart TZ-22 00PTf=3.6-82.8mm Pan 360ºContinuousTilt-5º～ 92º Section 2 Normal Operation Section 3 Menu Configuration 1 Move joystick to position the cursor beside menu selection 4 Press iris Close to cancel selectionAuto Zooming Tracking Dome Camera User Manual PTOL：PELCO-D COMM：2400,N,8,1 ADDR：0RESET CAMERA REBOOT SYSTEM LANGUAGE ENGLISH EXIT 3.1 Main Menu3.2 Select Language SYSTEM INFORMATION DISPLAY SETUP DOME SETTINGS DOME SETTINGS3.3 System Information SYSTEM INFORMATIONFigure 3.2 SYSTEM INFORMATION 3.4 Display Setup 3.4.1 Display Setup ZONE CAMERA PRESET SAVE RESET AZIMUTHZOOM 3.4.2 Label PositionPRESET NUMBER 256 BACK EXIT 3.5 Dome Settings 3.5.1 Dome Settings3.5.2 Camera Settings DOME SETTINGS1 CAMERA MOTION POWER UP PRESETS PATTERNS ZONES CLEARZoom limit enables you to define a limitation on zooming times 3.5.2.1 Program AE ModeLOW LIGHT MODE AE MODEBRIGHT LEVEL LOW LIGHT LIMITIRIS LEVEL AGC LEVELLOW LIGHT LIMIT 3.5.2.2 Other MenuIR CUT FILTER SHUTTERAUTO IRIS AUTO WHITE BALANCE AUTO SHARPNESSAUTO FILP 3.5.3 Motion SettingPROPORTIONAL PAN PARK TIMEPARK ACTION SET MANUAL LIMIT SCAN SPEEDSET SCAN STOPS CLEAR SCAN STOPSCLEAR AZIMUTH ZERO 3.5.4 Power UpPOWER UP ACTION SET AZIMUTH ZERO3.5.5 Presets Setting PRESETS PRESET NUMBER1 …PRESET NOT DEFINEO… EDIT PRESET LABELEDIT PRESET SCAENE CLEAR PRESET BACK EXIT 2 Edit preset label 1 Select preset numberPROGRAME PATTERN 3.5.6 Patterns Setting3 Edit preset scene 4 Clear a presetCLEAR PATTERN 3.5.7 Zone SettingTO program a zone To edit a zone labelFigure 3.15 ZONE SETTING 3.5.8 Clears Setting To clear a zoneCLEAR ZONES RESTORE FACTORY DEFAULTS 3.5.9 Presets Number3.6 Dome Settings 2 Menu CLEAR PRESETSSEQUENCESECS 3.6.1 AlarmsALARM NUMBER RESET DELAYSECS3.6.2 Alarms Setting Select alarm numberSelect alarm priority Set alarm action 3.6.3 Aux Setting Set alarm contactSet auxiliary to activate 3.6.4 Password Setting ENABLE PASSWORD Style 3.6.5 Windows BlankingBlanking Parameters 3.6.6 Set WindowsOperation 3.6.7 Edit Windows Location3.6.8 Edit Windows Zoom EDIT WINDOWS IRIS OPEN TO CONTINUE IRIS CLOSE TO CANCELEDIT WINDOW LOCATION HEATER MODE 3.6.9 Heater SettingTEMPERATURE SET HEATER DISPLAY3.6.10 Cruise Setting 3.6.11 Tracking Setting 2. Press Open 3. Move joystick to select desired parameter Auto Zooming Tracking Dome Camera User ManualOperations 1. In the menu of Fig 3.30, move joystick to a specific item3.6.12 Tracking Boundary 3.8 Other Functions RESET CAMERAREBOOT SYSTEM 3.7 Dome Label