Manuals / Optiview / Photography / Security Camera

Optiview TRKPTZ-18NX, TRKPTZ -26NX Set Azimuth Zero, Clear Azimuth Zero, Power Up Action

Models: TRKPTZ -26NX

1 53

Download 53 pages 12.57 Kb

Page 30

Image 30

Auto Zooming Tracking Dome Camera User Manual

(3) Follow the directions displayed on the monitor.

SET AZIMUTH ZERO:

Azimuth is the pan angle from 0°to 359°.Azimuth zero is the pan position you specify to be the 0°point. Azimuth zero is normally set to magnetic north. Once set, azimuth and compass readings are based on the set Azimuth Zero point.

To program azimuth zero:

(1)Move joystick to position the cursor beside set azimuth

zero.

(2)Press iris Open.

(3)Follow the directions displayed on the monitor.

CLEAR AZIMUTH ZERO:

(1)Move joystick to position the cursor beside CLEAR AZIMUTH ZERO.

(2)Press iris Open

(3)Follow the directions displayed on the monitor.

3.5.4Power Up

Move joystick to select <power up>, press Open to enter the power up menu shown as Fig3.10.

POWER UP

POWER UP ACTION NONE

BACK

EXIT

Figure 3.10 POWER UP

POWER UP ACTION:

Page 30

Image 30

Optiview TRKPTZ-18NX, TRKPTZ -26NX user manual Set Azimuth Zero, Clear Azimuth Zero, Power Up Action

Contents

User Manual Auto Zooming TrackingDome Cameras Contents 3.7 Dome Label 3.8 Other FunctionsSection1 Instruction 1.1 Production Introducing1.2 Character 1.3 Function Description Page  Target is not in the center of image Auto Zooming Tracking Dome Camera User ManualThe camera will not auto focus in the following status  Targets are in near and far at the same time14 Random Scan 17 Alarms Alarms input 1.4 Specification Comparison Chart TZ-22 00PTf=3.6-82.8mm Pan 360ºContinuousTilt-5º～ 92º Section 2 Normal Operation Section 3 Menu Configuration PTOL：PELCO-D COMM：2400,N,8,1 ADDR：0 4 Press iris Close to cancel selectionAuto Zooming Tracking Dome Camera User Manual 1 Move joystick to position the cursor beside menu selectionSYSTEM INFORMATION DISPLAY SETUP DOME SETTINGS DOME SETTINGS 3.1 Main Menu3.2 Select Language RESET CAMERA REBOOT SYSTEM LANGUAGE ENGLISH EXIT3.3 System Information SYSTEM INFORMATIONFigure 3.2 SYSTEM INFORMATION 3.4 Display Setup 3.4.1 Display Setup 3.4.2 Label Position ZONE CAMERA PRESET SAVE RESET AZIMUTHZOOMDOME SETTINGS1 CAMERA MOTION POWER UP PRESETS PATTERNS ZONES CLEAR 3.5 Dome Settings 3.5.1 Dome Settings3.5.2 Camera Settings PRESET NUMBER 256 BACK EXIT3.5.2.1 Program AE Mode Zoom limit enables you to define a limitation on zooming timesAE MODE LOW LIGHT MODEAGC LEVEL LOW LIGHT LIMITIRIS LEVEL BRIGHT LEVELSHUTTER 3.5.2.2 Other MenuIR CUT FILTER LOW LIGHT LIMITAUTO IRIS AUTO SHARPNESS AUTO WHITE BALANCE3.5.3 Motion Setting AUTO FILPPROPORTIONAL PAN PARK TIMEPARK ACTION CLEAR SCAN STOPS SCAN SPEEDSET SCAN STOPS SET MANUAL LIMITSET AZIMUTH ZERO 3.5.4 Power UpPOWER UP ACTION CLEAR AZIMUTH ZERO3.5.5 Presets Setting PRESETS PRESET NUMBER1 …PRESET NOT DEFINEO… EDIT PRESET LABELEDIT PRESET SCAENE CLEAR PRESET BACK EXIT 1 Select preset number 2 Edit preset label4 Clear a preset 3.5.6 Patterns Setting3 Edit preset scene PROGRAME PATTERN3.5.7 Zone Setting CLEAR PATTERNTO program a zone To edit a zone labelFigure 3.15 ZONE SETTING 3.5.8 Clears Setting To clear a zoneCLEAR ZONES CLEAR PRESETS 3.5.9 Presets Number3.6 Dome Settings 2 Menu RESTORE FACTORY DEFAULTSRESET DELAYSECS 3.6.1 AlarmsALARM NUMBER SEQUENCESECS3.6.2 Alarms Setting Select alarm numberSelect alarm priority Set alarm action 3.6.3 Aux Setting Set alarm contactSet auxiliary to activate 3.6.4 Password Setting ENABLE PASSWORD 3.6.5 Windows Blanking Style3.6.6 Set Windows Blanking Parameters3.6.7 Edit Windows Location Operation3.6.8 Edit Windows Zoom EDIT WINDOWS IRIS OPEN TO CONTINUE IRIS CLOSE TO CANCELEDIT WINDOW LOCATION HEATER MODE 3.6.9 Heater SettingHEATER DISPLAY TEMPERATURE SET3.6.10 Cruise Setting 3.6.11 Tracking Setting 1. In the menu of Fig 3.30, move joystick to a specific item Auto Zooming Tracking Dome Camera User ManualOperations 2. Press Open 3. Move joystick to select desired parameter3.6.12 Tracking Boundary 3.7 Dome Label RESET CAMERAREBOOT SYSTEM 3.8 Other Functions