Manuals / Optiview / Photography / Security Camera

Optiview TRKPTZ-18NX, TRKPTZ -26NX user manual Zone Setting, Clear Pattern

Models: TRKPTZ -26NX

1 53

Download 53 pages 12.57 Kb

Page 34

CLEAR PATTERN:

Auto Zooming Tracking Dome Camera User Manual

(2)Move the joystick up or down to view selections. Press iris Open to confirm selection.

(3)Move joystick to position the cursor beside PROGRAM PATTERN.

(4)Press iris Open.

(5)Follow the directions displayed on the monitor.

After a pattern is programmed, the remaining storage percentage will be displayed on the screen. This is the amount of memory available to program the remaining patterns.

CLEAR PATTERN:

(1)Move joystick to position the cursor beside CLEAR PATTERN.

(2).Press iris Open.

(3)F0llow the directions displayed on the monitor.

3.5.7Zone Setting

Move joystick to select <ZONES>, then press Open to enter the zones menu shown as Fig 3.14.

ZONES
ZONE NUMBER	1

…ZONE NOT DEFINEO… <EDIT ZONE LABEL> <EDIT ZONE>

ZONE ENABLED ON <CLEAR ZONE >

BACK

EXIT

Figure 3.14 ZONES SETTING

33

Image 34

Optiview TRKPTZ-18NX, TRKPTZ -26NX user manual Zone Setting, Clear Pattern

Contents

Auto Zooming Tracking User ManualDome Cameras Contents 3.7 Dome Label 3.8 Other Functions1.1 Production Introducing Section1 Instruction1.2 Character 1.3 Function Description Page  Target is not in the center of image Auto Zooming Tracking Dome Camera User ManualThe camera will not auto focus in the following status  Targets are in near and far at the same time14 Random Scan 17 Alarms Alarms input 1.4 Specification Comparison Chart 00PT TZ-22f=3.6-82.8mm Pan 360ºContinuousTilt-5º～ 92º Section 2 Normal Operation Section 3 Menu Configuration PTOL：PELCO-D COMM：2400,N,8,1 ADDR：0 4 Press iris Close to cancel selectionAuto Zooming Tracking Dome Camera User Manual 1 Move joystick to position the cursor beside menu selectionSYSTEM INFORMATION DISPLAY SETUP DOME SETTINGS DOME SETTINGS 3.1 Main Menu3.2 Select Language RESET CAMERA REBOOT SYSTEM LANGUAGE ENGLISH EXITSYSTEM INFORMATION 3.3 System InformationFigure 3.2 SYSTEM INFORMATION 3.4 Display Setup 3.4.1 Display Setup 3.4.2 Label Position ZONE CAMERA PRESET SAVE RESET AZIMUTHZOOMDOME SETTINGS1 CAMERA MOTION POWER UP PRESETS PATTERNS ZONES CLEAR 3.5 Dome Settings 3.5.1 Dome Settings3.5.2 Camera Settings PRESET NUMBER 256 BACK EXIT3.5.2.1 Program AE Mode Zoom limit enables you to define a limitation on zooming timesAE MODE LOW LIGHT MODEAGC LEVEL LOW LIGHT LIMITIRIS LEVEL BRIGHT LEVELSHUTTER 3.5.2.2 Other MenuIR CUT FILTER LOW LIGHT LIMITAUTO IRIS AUTO SHARPNESS AUTO WHITE BALANCE3.5.3 Motion Setting AUTO FILPPARK TIME PROPORTIONAL PANPARK ACTION CLEAR SCAN STOPS SCAN SPEEDSET SCAN STOPS SET MANUAL LIMITSET AZIMUTH ZERO 3.5.4 Power UpPOWER UP ACTION CLEAR AZIMUTH ZEROPRESETS PRESET NUMBER1 …PRESET NOT DEFINEO… EDIT PRESET LABEL 3.5.5 Presets SettingEDIT PRESET SCAENE CLEAR PRESET BACK EXIT 1 Select preset number 2 Edit preset label4 Clear a preset 3.5.6 Patterns Setting3 Edit preset scene PROGRAME PATTERN3.5.7 Zone Setting CLEAR PATTERNTo edit a zone label TO program a zoneFigure 3.15 ZONE SETTING To clear a zone 3.5.8 Clears SettingCLEAR ZONES CLEAR PRESETS 3.5.9 Presets Number3.6 Dome Settings 2 Menu RESTORE FACTORY DEFAULTSRESET DELAYSECS 3.6.1 AlarmsALARM NUMBER SEQUENCESECSSelect alarm number 3.6.2 Alarms SettingSelect alarm priority Set alarm action Set alarm contact 3.6.3 Aux SettingSet auxiliary to activate 3.6.4 Password Setting ENABLE PASSWORD 3.6.5 Windows Blanking Style3.6.6 Set Windows Blanking Parameters3.6.7 Edit Windows Location OperationEDIT WINDOWS IRIS OPEN TO CONTINUE IRIS CLOSE TO CANCEL 3.6.8 Edit Windows ZoomEDIT WINDOW LOCATION HEATER DISPLAY 3.6.9 Heater SettingTEMPERATURE SET HEATER MODE3.6.10 Cruise Setting 3.6.11 Tracking Setting 1. In the menu of Fig 3.30, move joystick to a specific item Auto Zooming Tracking Dome Camera User ManualOperations 2. Press Open 3. Move joystick to select desired parameter3.6.12 Tracking Boundary 3.7 Dome Label RESET CAMERAREBOOT SYSTEM 3.8 Other Functions