Manuals / Optiview / Photography / Security Camera

Optiview TRKPTZ -26NX, TRKPTZ-18NX user manual Normal Operation

Models: TRKPTZ -26NX

1 53

Download 53 pages 12.57 Kb

Page 13

Section 2 Normal Operation

Auto Zooming Tracking Dome Camera User Manual

Section 2 Normal Operation

These operating instructions cover the basic operation of the dome and its features. When the dome is used with other manufacturers‟ control system, please refer to the system controller‟s instructions. In the event of special requirements outside the scope of this document it is prefer to contact your local distributor.

Below instructions are based on using control keyboard as controlling device.

(1) Dome Self-testing after Powered up

After powered up, the dome will conduct reset procedure. In this procedure, the dome firstly pans to the default horizontal origin point, and finally tilts to the vertical 45 ° position to complete the self-testing. After the dome stops, it means the camera has completed the self-testing and is ready to receive control commands.

(2)Pan and tilt: Move joystick up, down, right, left.

(3)Set up preset

Move to next position. Then press PRESET + NUM （preset NO.）+ ENTER and the dome will save current horizontal angle and title angle of pan / tilt / zoom and position parameters into memory.

(4) Call preset

Press PRESET + NUM（Preset NO.）+ ENTER , and the

12

Image 13

Optiview TRKPTZ -26NX, TRKPTZ-18NX user manual Normal Operation

Contents

Auto Zooming Tracking User ManualDome Cameras Contents 3.8 Other Functions 3.7 Dome Label1.1 Production Introducing Section1 Instruction1.2 Character 1.3 Function Description Page The camera will not auto focus in the following status Auto Zooming Tracking Dome Camera User Manual Target is not in the center of image  Targets are in near and far at the same time14 Random Scan 17 Alarms Alarms input 1.4 Specification Comparison Chart 00PT TZ-22f=3.6-82.8mm Pan 360ºContinuousTilt-5º～ 92º Section 2 Normal Operation Section 3 Menu Configuration Auto Zooming Tracking Dome Camera User Manual 4 Press iris Close to cancel selectionPTOL：PELCO-D COMM：2400,N,8,1 ADDR：0 1 Move joystick to position the cursor beside menu selection3.2 Select Language 3.1 Main MenuSYSTEM INFORMATION DISPLAY SETUP DOME SETTINGS DOME SETTINGS RESET CAMERA REBOOT SYSTEM LANGUAGE ENGLISH EXITSYSTEM INFORMATION 3.3 System InformationFigure 3.2 SYSTEM INFORMATION 3.4 Display Setup 3.4.1 Display Setup ZONE CAMERA PRESET SAVE RESET AZIMUTHZOOM 3.4.2 Label Position3.5.2 Camera Settings 3.5 Dome Settings 3.5.1 Dome SettingsDOME SETTINGS1 CAMERA MOTION POWER UP PRESETS PATTERNS ZONES CLEAR PRESET NUMBER 256 BACK EXITZoom limit enables you to define a limitation on zooming times 3.5.2.1 Program AE ModeLOW LIGHT MODE AE MODEIRIS LEVEL LOW LIGHT LIMITAGC LEVEL BRIGHT LEVELIR CUT FILTER 3.5.2.2 Other MenuSHUTTER LOW LIGHT LIMITAUTO IRIS AUTO WHITE BALANCE AUTO SHARPNESSAUTO FILP 3.5.3 Motion SettingPARK TIME PROPORTIONAL PANPARK ACTION SET SCAN STOPS SCAN SPEEDCLEAR SCAN STOPS SET MANUAL LIMITPOWER UP ACTION 3.5.4 Power UpSET AZIMUTH ZERO CLEAR AZIMUTH ZEROPRESETS PRESET NUMBER1 …PRESET NOT DEFINEO… EDIT PRESET LABEL 3.5.5 Presets SettingEDIT PRESET SCAENE CLEAR PRESET BACK EXIT 2 Edit preset label 1 Select preset number3 Edit preset scene 3.5.6 Patterns Setting4 Clear a preset PROGRAME PATTERNCLEAR PATTERN 3.5.7 Zone SettingTo edit a zone label TO program a zoneFigure 3.15 ZONE SETTING To clear a zone 3.5.8 Clears SettingCLEAR ZONES 3.6 Dome Settings 2 Menu 3.5.9 Presets NumberCLEAR PRESETS RESTORE FACTORY DEFAULTSALARM NUMBER 3.6.1 AlarmsRESET DELAYSECS SEQUENCESECSSelect alarm number 3.6.2 Alarms SettingSelect alarm priority Set alarm action Set alarm contact 3.6.3 Aux SettingSet auxiliary to activate 3.6.4 Password Setting ENABLE PASSWORD Style 3.6.5 Windows BlankingBlanking Parameters 3.6.6 Set WindowsOperation 3.6.7 Edit Windows LocationEDIT WINDOWS IRIS OPEN TO CONTINUE IRIS CLOSE TO CANCEL 3.6.8 Edit Windows ZoomEDIT WINDOW LOCATION TEMPERATURE SET 3.6.9 Heater SettingHEATER DISPLAY HEATER MODE3.6.10 Cruise Setting 3.6.11 Tracking Setting Operations Auto Zooming Tracking Dome Camera User Manual1. In the menu of Fig 3.30, move joystick to a specific item 2. Press Open 3. Move joystick to select desired parameter3.6.12 Tracking Boundary REBOOT SYSTEM RESET CAMERA3.7 Dome Label 3.8 Other Functions