[INTVideo] internal video setting screen

When [Memory] has been selected

Described below are the write and preview procedures for “Still” (still picture) or “Movie” (moving picture). It is possible to set the number of frames (number of pages) that can be used to a maximum of 30 (NTSC) or 26 (PAL). However, if pages are allocated to titles, the number of pages will be reduced by the equivalent amount. The page allocation can be changed on the “Setup” initial setting screen.

Write procedure

When Frame = 1

 

 

 

 

 

 

 

 

 

Use the rotary 5 control to set the mode to “Write.”

 

R1

 

R2

 

R3

 

R4

 

R5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Memory

 

Page

 

Frame

 

 

 

 

Mode

Use the rotary 2 control to select the page on which the

 

 

 

 

 

 

 

 

 

1

 

1

 

 

Field

 

Write

images are to be written.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Use the rotary 3 control to set the number of frames to be

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 - 30/26

 

 

1 - 30/26

 

 

Field

 

 

Write

 

written. Set 1 as the number of frames for Still writing and

 

 

 

(NTSC/PAL)

 

 

(NTSC/PAL)

 

 

Frame

 

 

Preview

 

set a number greater than 1 for Movie writing.

 

 

 

 

 

 

 

 

 

 

 

 

Exit

 

 

 

 

 

 

 

 

 

 

 

 

Check the image to be written at the Prog output, and

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

when the image to be written appears, write it using

When Frame > 1

 

 

 

 

 

 

 

 

 

“Enter.” In the case of Movie, the images are written

 

R1

 

R2

 

R3

 

R4

 

R5

consecutively from the page designated by the rotary 2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

control up to the page equivalent to the number of frames

 

Memory

 

Page

 

Frame

 

 

 

 

Mode

designated by the rotary 3 control. Any existing data will

 

 

1

 

 

5F

 

Repeat

 

Write

be deleted in the process of image writing.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 - 30/26

 

 

1 - 30/26

 

 

Repeat

 

 

Write

 

 

 

 

 

 

 

 

 

 

 

 

Preview procedure

 

 

 

(NTSC/PAL)

 

 

(NTSC/PAL)

 

 

Once

 

 

Preview

 

 

 

 

 

 

 

 

 

 

 

 

 

Exit

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Use the rotary 5 control to set the mode to “Preview.”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Use the rotary 2 control to select the page on which the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

images are to be previewed. To preview Still, use the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

rotary 4 control to select “Field” output or “Frame” output.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

To preview Movie, use the rotary 3 control to set the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

number of frames to be previewed and the rotary 4 control

 

 

 

 

 

 

 

 

 

 

 

 

 

 

to select “Repeat” (repeat) playback or “Once” (once-only)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

playback. If a value exceeding the number of frames

 

 

 

 

 

 

 

 

 

 

 

 

 

 

written has been set by the rotary 3 control, the setting will

 

 

 

 

 

 

 

 

 

 

 

 

 

 

be ignored.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Start the preview using “Enter.” Even when the page selected by the rotary 2 control is midway through the Movie, the Movie is played back from its beginning.

If the settings are acceptable, use the rotary 5 control to set the mode to “Exit”, then enter the settings using “Enter.” The page set is recalled by the “INTVideo” button and played back.

Even when another “Matte” or “CustomColor” selection has been set using “INTVideo” upon completion of the settings, the images previously stored in the memory can be read by selecting “Memory” again but they will be cleared after the power is turned off.

The playback trigger is applied using “Shift” + “.”.

The “Grade” setting which was set by “BackMatte” also takes effect for “Memory.”

<Note>

Images cannot be written during Movie playback. If images are to be written, first set [Mode] to [Exit] and press the [Enter] button to exit Movie playback, and then proceed.

22

Page 22
Image 22
Panasonic AG-MX70 manual When Memory has been selected, When Frame =, Memory Frame Mode, Field Write, Repeat Write