[Setup] initial setting screen
[System1] setting
This is used to perform a variety of settings. | R1 |
| R2 |
| R3 |
| R4 |
| R5 | ||||
|
|
|
|
|
|
|
|
|
|
|
|
| |
The rotary 2 control is used to set the amount of delay for | System1 |
| Dly |
| Time |
| GPI |
| RS422 | ||||
the source input when the [AdvRef] advanced reference |
|
| 1Frame |
| Sec |
| ME |
| GVG | ||||
signal is connected with the 3D optional board |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| 1Frame |
|
| Sec |
|
| ME |
|
| GVG |
| |
installed. If 0Frame is selected, the video delay amount is |
|
|
|
|
|
|
|
|
| ||||
|
| 0Frame |
|
| Frame |
|
| DSK |
|
| SONY |
| |
different between when the 3D effects are applied and when |
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| Fade |
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| ||
they are not. The default setting is 1Frame. The setting is |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
fixed at 0Frame when the 3D optional board is not installed. |
|
|
|
|
|
|
|
|
|
|
|
|
|
The audio source delay amount is also set according to this setting.
[Sec] (seconds + frames) or [Frame] (frames) only is selected for the time display using the rotary 3 control. The default setting is [Sec].
Whether [ME], [DSK] or [Fade] is to be executed by GPI can be set using the rotary 4 control. The default setting is [ME]. [GVG] or [SONY] can be selected as the
[System2] setting
The time taken until the LCD is set to the power saving | R1 |
| R2 |
| R3 |
| R4 |
|
| R5 | ||
|
|
|
|
|
|
|
|
|
|
|
| |
mode can be selected using the rotary 2 control. | System2 |
| LCDStby |
| VBClean |
| DR |
|
|
| ||
With the 0 setting, the display is always on. The time can |
| 0 |
|
| Off |
|
| On |
| |||
be set in |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| 0 - 60 |
|
| On |
|
| On |
|
|
| |
setting is 0. |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
| Off |
|
| Off |
|
|
| |
[On] or [Off] is selected using the rotary 3 control to set |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
whether or not cleaning is to be performed inside the vertical |
|
|
|
|
|
|
|
|
|
|
|
|
blanking period (VBlk). The default setting is [Off]. |
|
|
|
|
|
|
|
|
|
|
|
|
[On] or [Off] is selected using the rotary 4 control to set whether or not the [DR] (dynamic rounding) is to be performed. The default setting is [On].
<Note>
Selecting [Off] for [VBClean] may result in a deviation in the amount of delay between the video signals and vertical blanking signals depending on the setting for the [Dly] item among the [System1] settings and on whether the 3D optional board (AG- VE70) has been installed.
[Bus] setting
AB (AB bus) or PrgPre (program/preset system) can be | R1 |
| R2 |
| R3 |
| R4 |
| R5 | ||||
|
|
|
|
|
|
|
|
|
|
|
|
| |
selected as the bus system using the rotary 2 control. The | Bus |
| Type |
| Still |
| Audio |
| Tally | ||||
default setting is AB. |
|
| AB |
| On |
| CP | 8 |
| ||||
[On] (initiate Still) or [Off] (do not initiate Still) when cross |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| AB |
|
| On |
|
| CP |
|
| 8 |
| |
points are to be changed is selected using the rotary 3 |
|
|
|
|
|
|
|
|
| ||||
|
| Prg Pre |
|
| Off |
|
| 1, 2 |
|
| EXT |
| |
control. The default setting is [On]. |
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Audio MIX system can be selected using the rotary 4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
control. |
|
|
|
|
|
|
|
|
|
|
|
|
|
At the [CP] setting, two audio sources allocated to the selected cross point are output. At the [1,2] setting, the audio sources 1, 2 allocated to the cross point are mixed at all times. The default setting is [CP].
[8]or [EXT] can be selected using the rotary 5 control as the setting for the eight tally outputs. At the [8] setting, the tally signal is output when cross point 8 has been selected; at the [EXT] setting, it is output when EXT has been selected.
<Note>
When [Still] is to be set to [Off], do not mix the analog and SDI signals for the input. Be absolutely sure to use the
56
