Installation of the AG-VE70 | Panasonic AG-MX70 instruction

Installation of the AG-VE70

The AG-VE70 is a 3D effect board that enables the 3D patterns, etc. of the AG-MX70 to be used. Follow the procedure below to install it.

<Note>

Always consult your dealer or authorized service center regarding installation of the AG-VE70 in the AG-MX70.

1) Turn off the power of the AG-MX70, remove the ten screws from the bottom panel, and detach the top part including the LCD. Refrain from using any force

to pull the top part away from the bottom part since Screws (a 10) the two parts are still connected by cables.

2) Remove the 20 screws, and remove the shield plate.

3)Refer to the figure on the left, and insert the AG-

VE70.

4)Remove the five screws provided on the five hexagonal posts in the center of the motherboard.

(Refer to the figure on page 100.)

	5) In the same way, plug the cable attached to the AG-	3)
	VE70 into the AG-MX70. Route the wires while	3)
	VE70 into the AG-MX70. Route the wires while

carefully ensuring that they do not make contact with
the transition lever unit.	5)

6) Secure the five screws which were removed in step 4).

7)Secure the screws which were removed in steps 2) and 1).

Specifications

[AG-YA70]

(SDI interface board: optional accessory)

Power Source: DC 5 V, 3.3 V

Power Consumption: 6.3 W

[AG-VE70]

(3D effect board: optional accessory)

Power Source: DC 5 V, 3.3 V

Power Consumption: 6.1 W

indicates safety information.

indicates safety information.

Operating temperature: 41 °F to 104 °F (+ 5 °C to + 40 °C)

Operating humidity: Less than 80%

Standard:SMPTE-259M-C standard complied with

Operating temperature: 41 °F to 104 °F

	(+ 5 °C to + 40 °C)
Operating humidity:	Less than 80%

101

Image 101

Panasonic AG-MX70 manual Installation of the AG-VE70

Contents

AG- P FCC Note Overview Contents About this software SpecificationsOverview of MX-Navi Processing of image data Before use Parts and their functions ONE WAY button REV reverse buttonMIX button LUM luminance key button Preset bus / Still execution button Preset bus selector buttonPreset bus / Strobe execution button Preset bus / Video Effects execution Button Setting page display area Item, parameter setting areaJoystick, Z parameter display area Audio level meter INT Video internal video setting Display button SET UP initial setting page display buttonAudio Effects audio effect setting Display button Audio Effects on audio effect Execution button Time time setting rotary control Phone headphone volume controlPattern transition/key pattern number Setting button ME ME transition/key transition time setting button Preset / Source 1/5 selector button 1SHIFT key 9B/PRESET / Source 4/8 selector buttonPreset / Source 2/6 selector button Preset / Source 3/7 selector button Source 2/6 fader 1SOURCE 1/5 fader 4SOURCE 4/8 faderSource 3/7 fader AUX 1 fader MIC input connector External key input connectorExternal input Y connector External input PB connector = ? Editor interface connector 9-pin Analog audio 3 input connectorsTally output connector RS-422A/RS-232C selector switch ≥ Functions that can be controlled from the AG-A850 External interfaces≥ Connections ≥ Connection of conversion cable Example 2 Live application System DiagramExample 1 Live application Example 3 Editing application CD player, etc PC with MX-Navi already installedVideo camera Editing controller Setting panel screen Power supply and backupINTVideo internal video setting screen 00E When Custom1, 2 has been selected When Back Matte has been selectedBack Color Level Pattern Grade Matte White 255 Black Color Set Pattern Matte Custom1 BackM When Frame = When Memory has been selectedMemory Frame Mode When Frame Color Effect Gain 128 Color Effects setting screen00 E 1000 F 3015 1000F Video Effects setting screenPos 128 Channel display Scrolled display Defocus setting Mosaic settingMono monochrome setting Mosaic Size Off Defocus Level Time Screen Effects Still Field 10F Time Effects still/strobe setting Paint setting Decay settingNega negative setting Mirror setting Decay Time Off Paint Level Nega 3D setting Video Effects setting screen Execution of Effects Preset program transmissionAB transition DSK key 1000 F 0013 Wht Effect-by-effect setting screensTransition wipe pattern settings Pattern Width Color Edge Hard White Pattern Edge setting Effects Light Off Effects settingEffects Light Shadow Effects Time Light Trail Self Key setting Pos 128 196 Chroma Key setting00E 1000F 3101 Wht Key Slice Slope Level 128 255 Crop setting Color Offset Slice Area Mono L Cancel Color cancel settingBorder setting Crop 00E 1000F 3102 Wht Luminance Key and EXT Key external key settingsKey setting Pos 128 00E 1000F 9501 Title Key settingKey setting 00E 1000F 3002 Basic Pattern Key setting numbers 3001 to 1000F 3301 Wht Other key settings numbers 3301 and up 3Dmodify setting Effect-by-effect setting screens Empty Modify 9000 Setup Key Learn setting Frame Level Copy 255 Paste Rotate Time TransF Exit 128 00 E 1000 F 3013 Frame Level Copy 255 Paste Width Angle Time Amp Exit 192 With flag #6002 Insert Replace FlagWith accordion #6003 Insert Replace Frame Level Copy 255 Paste Width Angle Amp Exit 192 Pattern number selected Processing after cancel operation 00E 1000F DSK/Fade settingsDSK Source settings DSK On/Off setting DSK Key settingsCrop setting Fade Audio Phone Black After White Off Pre Blue Fade settings PAN setting Audio Effects settings00E 1000F Wht Balance EQ Mid equalizer midrange setting EQ equalizer settingVoice Change voice changer setting Mute setting Wash Ph 128 Pr 196 Setup initial setting screen1000F 3015 Wht Direct Pattern setting Power power on setting 00 E 1000 F Wht 00 E 1000 F 3015 WhtExample of transition Pos 128 196 Example of key pattern Pos 128 Y 196 Factory settings Audio Input Video Setup Default Link Audio Video Input settingsSetting method 3015 Wht Video Format setting Memory settingGen Lock external synchronization setting Bus setting System1 settingSystem2 setting File setting Audio Level setting Setting method Other settingsRecall method Clearing events Number key priorities Correlation between number key settings and Pattern buttonTransition time selection Pair Transition patterns 100 101 102 DVE CUT SAT MIX 1301 1302 1303 1304 1305 1306 1307 1308 139 140 MIX 3D DVE LUM Key patterns 3305 Exp 3315 4701 4702 4703 4704 4705 4706 4707 4708 4730 4731 4732 4733 4769 4770 4771 4772 4773 +Diss 4789 4790 4791 4792 4793 28 T-29 T-30 10 T-11 T-12 9711 9721 9731 14 T-15 17 T-18 T-19 22 T-23 T-24 Overview of MX-Navi About this softwareUSB driver MX-Navi Processing of image data ≥ Memory capacity Management of the image memory Before use Installation of the USB driverAG-MX70 connections For Windows 98 and Windows 2000 Notes For Windows XP Note Operation confirmation Installation of MX-Navi Screen descriptions Startup and shutdown Icon 9NAME/COMMENT Edit menu Menu descriptionsFile menu Cursor menu View menu Help menu Operation menuTool menu Title data operations Setting the Title data playback propertiesFlow until Title data playback Registering Title data in the transmission list ≥ Effect Clearing Title data Manual transmission and playback of Title dataAutomatic transmission and playback of Title data Reordering the transmission list Checking the Title data imageSaving the transmission list Opening a transmission list Checking the memory status of the AG-MX70 Changing the AG-MX-70 memory settingsOther operations Clearing IntVideo data Transmission and playback of IntVideo dataSaving data Recalling events Still Duration Setting the initial propertiesMovie Duration Roll Speed Boot and shutdown Setting the operating environmentMemory management File Management Left arrow List of short-cut keysDown arrow Open the properties of the selected data Problem What to check Before calling for service ≥Update the video card driver to the newest version General Specifications Video INPUT/OUTPUT Accessories Installation of the AG-YA70 AG-VE70 Installation of the AG-VE70 Panasonic Broadcast & Television Systems Company