Panasonic AJ-HDC27V, AJ- P 1, 2, 3, 4 5

109

2,5

EMERGENCY

screw

<Notes>

ODo not turn the EMERGENCY screw except in an

emergency.

ODo not turn the screw clockwise. Stop turning the

screw as soon as the tape is ejected. Otherwise,

the mechanism may be damaged.

OAfter the tape is ejected, the cassette holder will not

lock into place even when an attempt is made to

close it. Be sure to turn the power off and turn it

back on to reset the mechanism’s operation, and

then close the cassette holder.

OA clicking sound will be heard when the

EMERGENCY screw is turned: this sound is made

by the reel drive operation and is therefore not

indicative of a malfunction.

OThis screw needs to be rotated through about 20 turns

after the first turn until the unloading can be started.

OThis screw needs to be rotated through about 90 turns

after the first turn until the tape is ejected.

Emergency eject

If the cassette cannot be ejected by pressing the

EJECT button, use a screwdriver or similar tool to

press and turn the EMERGENCY screw. This

enables the cassette to be removed.

Error codes

One of the following error codes appears in the

display window when an error has occurred in the unit

for some reason.

1Set the power to OFF.

1Set the power to OFF.

2Remove the rubber cap where shown in the figure.

Insert a Phillips head screwdriver into the cross-

shaped part of the EMERGENCY screw (red).

3While pushing in with the screwdriver, turn the

EMERGENCY screw counterclockwise until the

tape is ejected.

OThis screw needs to be rotated through about 20

turns after the first turn until the unloading can

be started.

OThis screw needs to be rotated through about 90

turns after the first turn until the tape is ejected.

4Remove the cassette.

5Return the rubber cap to its original position.

4Cassette

holder

3Push in and turn at the same time.

Code No. Description of error

07 Pinch solenoid problem

08 Cleaning solenoid problem

0B Supply reel problem

0C Take-up reel problem

0D Capstan problem

0E Cylinder problem

0F Loading problem

3F Servo problem

Contents

Main WARNING: CAUTION: Page Contents Introduction Features of the camera unit Features of the VTR unit System Configuration Camera/VTR AJ-HDC27V Power supply section Accessory mounting section Audio function section (1) Audio function section (2) Viewfinder section function section (1) function section (2) function section (3) function section (4) function section (5) Warning/status display section Menu operation section Time code related section (1) Time code related section (2) Using the Anton/Bauer battery pack 1 2 Using the Panasonic AU-BP402 battery pack 1 Detach the battery mount. 3 2 4 Using the Sony NP-1 battery pack 1 2 3 Using the Sony BP-90 battery pack 1 2 1 2 3 Using the Sony BP-L60/L90 lithium- ion battery 1 2 Attaching the lens 1 2 3 4 Adjusting the lens flange 1 2 9 3 4 1 2 3 4 5 7 8 9 10 Page Page 1 2 3 When attaching a microphone to the viewfinder (optional accessory) for use 4 Page 1 2 When connecting a microphone to the MIC IN jack 1 2 When connecting a microphone to the AUDIO IN connector 1 2 3 4 5 1 2 When connecting audio components Mounting the unit on a tripod 1 2 Page Connecting the extension control unit Attaching the rain cover Page Viewfinder lamp displays Setting the lamp displays 4 3 Page Page Selecting the display items Selectable items Selecting the display items 4 3 Display modes and setting change messages Switching the display mode 3 Setting the marker displays 2 Setting the camera ID 4 3 Screen displays Displays relating to errors and warnings For details, refer to Warning system (pages 107 and 108). Displays relating to time codes Time code-related switch settings and display items 2 3 4 1 2 3 4 5 6 7 8 When the white balance cannot automatically be adjusted When there is no time to adjust the white balance White balance memories White balance search area When FILTER INH is set to ON Adjusting the black balance 1 2 3 4 Setting the electronic shutter 1 2 3 Setting the synchro scan mode 2 Setting the electronic shutter Changing the shutter speed and mode selection range 3 1 3 Scan reverse Setting the scan reverse 3 Adjusting the audio level Manual audio level adjustments Limiter 1 2 xx:xx:24:00 Setting the users bit 1 2 2,5 5 3 4 1 2 3 2,5 4 5 Externally locking the time code 1 2 3 4 Example of connections for external lock How to use the user data User data operation Saving the user data 5 How to eject the setup card How to insert the setup card Formatting the setup card 4 Saving the data settings on the card 2 7 3 5 6 12 11 10 9 6 7 Loading the data saved on the card 1 3 1 Ejecting the cassette tape Ejecting the cassette when the battery has no charge To prevent accidental erasure 2 1 From adjusting the white balance and black balance to stopping the recording 2 3 4 1- 4, 5 1-21-1, 1-2 2 3 4 1 2 Ensuring scene-to-scene continuity at other times 1 2 3 Playback Lens RET button functions Other VTR functions NEWS REC function RETAKE function INTERVAL REC (intermittent recording) function User menu Engineer menu User menu: Engineer menu Basic setting menu operations Displaying menus 1 2 1 2 3 Displaying sub-menus and deciding on settings 1 2 3 4 5 <Note> Items indicated with }are items whose settings can only be switched ON and OFF. Page Page Page Setting menu screens CAM MAIN MENU 1 screen CAM MAIN MENU 2 screen CAM MAIN MENU 3 screen CAM MAIN MENU 4 screen ROP screen The ROP (Remote Operation Panel) is set on this MATRIX screen The camera matrix is set on this screen. COLOR CORRECTION 1 screen The camera color saturation adjustments and hue adjustments are set on this screen. COLOR CORRECTION 2 screen The camera color saturation adjustments and hue adjustments are set on this screen. LOW SETTING screen The low level gain is set on this screen. MID SETTING screen The middle level gain is set on this screen. HIGH SETTING screen The high level gain is set on this screen. ADDITIONAL DTL 1 screen The special detail features of the camera are set on ADDITIONAL DTL2 screen SKIN TONE DTL screen The skin tone detail of the camera is set on this KNEE/LEVEL screen The knee settings of the camera are performed on this GAMMA screen The gamma settings of the camera are performed on CAMERA SETTING screen The basic settings of the camera are set to ON or OFF VF DISPLAY screen VF MARKER screen VF INDICATOR screen CAMERA ID screen The camera ID is set on this screen. SHUTTER SPEED screen The shutter speed is set on this screen. ! LED screen The display of the lamp which appears inside the viewfinder is set to ON or OFF on this screen. CAMERA SW MODE screen The modes of the camera switches are set on this SUPER GAIN screen The gain allocated to the SUPER GAIN switch is set FRAME MODE screen Setting menu screens CAM CARD R/W SELECT screen CAM CARD READ/WRITE screen Setting menu screens GENLOCK/IRIS screen The genlock and iris control settings are performed on LENS ADJ screen The lens adjustments are performed on this screen. CAM USER MENU SELECT 1, 2 and 3 screens CAM USER MENU SELECT 1 screen CAM USER MENU SELECT 2 screen CAM USER MENU SELECT 3 screen BLACK SHADING screen The black shading adjustments are performed on this WHITE SHADING screen The white shading adjustments are performed on this FLARE screen DIAGNOSTIC screen The usage statuses and software versions are displayed on this screen. EVALUATION screen OPTION screen The engineer menu display is selected on this screen. EVALUATION screen OS/N measurement screen The S/N measurements are performed on this screen. OResolution measurement screen The resolution measurements are performed on Setting menu screens VTR MAIN MENU screen FUNCTION screen The VTRs functions are set on this screen. BATTERY/TAPE screen BATTERY SETTING screen The type of battery to be used is selected and its settings are performed on this screen. VTR VF INDICATOR screen The information to be displayed in the viewfinder is set The MIC/AUDIO settings are performed on this Page The time code and users bit settings are performed on TIME DATE screen The time/date settings are performed on this screen. VTR USER MENU SELECT screen VTR CARD READ/WRITE screen VTR INITIALIZE screen Setting menu screens The maximum number of VTR unit items which can be registered is 14. FUNCTION screen BATTERY/TAPE screen Setting menu screens The maximum number of VTR unit items which can be registered is 14. VTR VF INDICATOR screen Warning system $SLACK $REC WARNING $RF $SERVO Warning system $HUMID $BATTERY NEAR END TAPE F BATT F 1 2 3 4 5 4 Maintenance Condensation Head cleaning Cleaning inside the viewfinder Phenomena inherent to CCD cameras 1 Preparation for inspection Inspecting the camera unit 2 3 1 2 3 4 6 7 Page Page [GENERAL] [CAMERA UNIT] [VTR UNIT] [Connector Section] VTR Video System VTR Audio System VTR Tape Transport System Input [VIEWFINDER] [ACCESSORIES] [RELATED COMPONENTS & PARTS] Relating to power supply Viewfinder F0601W @ Printed in Japan VQT9419 P