Panasonic AJ-SD955BE manual $ Displaying the “HOURS METER” information, $ UMID information display

CONTENTS

Error messages

$ Displaying the “HOURS METER” information

Turn the search dial to move the cursor (2).

The description for the item where the cursor is located is shown on the counter display.

No./Item	Description
Ser	Displays the unit’s serial No.
222222222
H00	Displays the time that the power has been
	supplied in one-hour units.
OPERATION
H01	Displays the time that the drum has been
	rotating in one-hour units.
DRUM RUN
H02	Displays the time that the tape has been running
	during FF, REW, PLAY, SEARCH (JOG, SLOW,
TAPE RUN	SHTL), REC, and EDIT modes (except for STILL
	in the JOG, SLOW or SHTL mode) in one-hour
	units.
H03	The number of times for threading (loading)/
	unthreading (unloading) is displayed in single
THREADING	units.
H04	Displays the number of times front loading has
	been performed in single units.
F LOADING
H11	Displays the time that the drum has been
	rotating in one-hour units. (Can be reset)
DRUM RUNr
H12	Displays the time that the tape has been running
	during FF, REW, PLAY, SEARCH (JOG, SLOW,
TAPE RUNr	SHTL), REC, and EDIT modes (except for STILL
	in the JOG, SLOW or SHTL mode) in one-hour
	units. (Can be reset)
H13	The number of times for threading (loading)/
	unthreading (unloading) is displayed in single
THREADINGr	units. (Can be reset)
H14	Displays the number of times front loading has
	been performed in single units.
F LOADINGr	(Can be reset)
H30	The number of times the power has been turned
	on is displayed in single units.
POWER ON

<Notes>

O The resettable items in the “HOURS METER” information are reset by the shop when performing maintenance or other work.

O The search buttons and the search dial cannot be operated while the DIAG menu is displayed.

If “T&S&M” is selected in the setup menu No. 008 (DISPLAY SEL), a message appears in the mode display whenever a warning or error occurs. When multiple events occur, the event with the highest priority is displayed.

Priority	Display/Description
High	Error messages (See error message table)
	When an operational malfunction has occurred in
	the unit, the error number flashes and the error
	message is indicated on the counter display.
	INT SG
	When SG has been selected as the input signal with
	the INPUT SELECT buttons, pressing the REC
	button or the EDIT button (E-E mode) will display
	“INT SG” for the first two seconds.
	This is also displayed for the first two seconds when
	starting editing.
	NO INPUT
	If there is no input signal (except for analogue audio)
	to the connector selected using the INPUT SELECT
	buttons, pressing the REC button or the EDIT button
	(E-E mode) will display “NO INPUT” for the first two
	seconds.
	This is also displayed for the first two seconds when
	starting editing.
	Warning messages (See error message table)
	When a warning occurs in this unit, the error number
	and warning message are indicated on the counter
	display.
Low	When multiple warnings occur, the warning with the
	highest priority is displayed.

$ UMID information display

This is displayed when UMID information is present on the input signal in E-E mode.

This lamp lights during tape playback when UMID information has been recorded on the tape. “NO-INFO” is displayed when there is no UMID information.

Item		Display/Description
MATNO	Material number
COPY	Instance number (No. of copies)
OWNR	Country, organization, user
POS	Reception status from GPS satellites when
	recording spatial coordinates (height above sea
	level, longitude and latitude):
	HOLD: No reception from any satellite
	2D:	Reception possible, but number of
		satellites is insufficient. Height above
		sea level will not be accurate.
	3D:	Good reception
DTAE	Date
TIME	UTC (Coordinated Universal Time) and time
	difference with UTC

67 (E)