When you experience problems with settings

Access Point Connection Setting

Access Point Connection Setting

Failed to connect to the access point.

A conflict with another device occurred.

Do you want to configure Access Point Connection

Setting again ?

YesNo

OK

Display

Check the following

A conflict with another

≥ Please wait a few moments,

device occurred.

and then try again.

 

 

 

≥ Setting of the Wireless router

 

(Access point) for MAC

A time out error occurred.

Address etc.

 

≥ The SSID and the encryption

 

key of the Wireless router

 

(Access point).

 

 

≥ Please wait a few moments,

An authentication error or a

and then try again.

time out error occurred.

 

 

 

 

≥ Connection of Wireless LAN

 

Adaptor

A device error occurred.

If there is no improvement in

 

symptom, contact our

 

Customer Service Center.

 

 

Network Easy Setting (Connection Check)

Network Easy Setting (Connection Check)

Complete.

 

1.

LAN cable connection

: Fail

2.

IP address setting

: Fail

3.

Connection to gateway

: Fail

 

 

LAN cable is not connected.

 

Please check the connection.

 

Select “Yes” and press [OK] to check network

connection again. Select “No” and press [OK]

to finish Network Easy Setting.

 

 

 

 

Yes

No

OK

 

 

Display

 

 

 

Check the

 

 

 

 

 

following

 

 

 

 

 

 

 

 

1. LAN cable connection or

: Fail

≥ Connection and

 

Connection to access point

settings of

 

 

 

 

2. IP address setting

 

: Fail

Wireless router

 

 

(Access point)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

≥ Connection of

 

3. Connection to gateway

: Fail

the LAN cables

 

 

 

 

 

 

 

(> 31)

 

 

 

 

 

 

 

 

1. LAN cable connection or

: Pass

≥ Connection and

 

Connection to access point

settings of

 

 

 

 

2. IP address setting

 

: Fail

Wireless router

 

 

(Access point)

 

 

 

 

 

 

 

 

3. Connection to gateway

: Fail

≥ Connection and

 

 

 

 

 

 

 

settings of the

 

1. LAN cable connection or

 

 

 

: Pass

hub and router

 

Connection to access point

 

 

 

≥ Settings of “IP

 

 

 

 

 

 

 

 

2. IP address setting

 

: Pass

Address/DNS

 

3. Connection to gateway

: Fail

Settings” (> 39)

 

 

 

 

 

 

 

 

 

 

Network

Network Easy Setting (Internet Connection Check)

 

Network Easy Setting (Internet Connection Check)

 

 

 

 

 

 

 

 

 

 

 

 

Complete.

 

 

 

 

 

 

- Connection to the Internet : Fail(Error code: B019)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Failed the connection test.

 

 

 

 

 

 

Cannot find the server.(Error code: B019)

 

 

 

 

 

 

Please refer to the operating instructions for the cause

 

 

 

 

 

of the error and the solution for it.

 

 

 

 

 

 

Press [OK].

 

 

 

 

 

 

OK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Display

 

 

Check the following

 

Cannot find the server.

 

≥ “Primary DNS” and “Secondary

 

(Error code: B019)

 

DNS” settings of “IP Address/DNS

 

 

Settings” (> 39)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

≥ The server may be busy or the

 

Failed to connect to

 

service may have been

 

 

suspended. Please wait a few

 

the server.

 

 

 

moments, and then try again.

 

(Error code: B020)

 

 

 

≥ Settings of “Proxy Server Settings”

 

 

 

 

 

 

 

 

(> 39) and the router

 

 

 

 

 

 

 

 

 

Refer to the operating instructions of the hub or router.

You can perform this setup anytime by selecting “Network Easy Setting” in the Setup menu. (> 32)

You can redo these settings individually using “Network Settings”. (> 39)

After performing network settings on this unit, the settings (encryption level, etc.) of the Wireless router (Access point) might change. When you have trouble getting online on your PC, perform the network settings on your PC in accordance with the settings of Wireless router (Access point).

VQT2J81

(ENG)

33

Page 33
Image 33
Panasonic DMP-B500 operating instructions When you experience problems with settings