Using the setup menu
Setting the lowpass filter
If the speaker sizes (➔ page 37) are set to “SMALL ”, make this setting.
The unit cannot reproduce the entire bass range when speakers are set as “SMALL ”. You can arrange the unit to provide missing bass sounds through the subwoofer by setting the lowpass filter frequency according to frequencies available for playback.
1.To enter the SETUP (➔ page 36)
2.Press [e][r] to select “FILTER FRQ ”, and press [OK] to confirm.
3.Press [e][r] to select the lowpass filter frequency, and press [OK] to confirm.
Lowpass filter frequency for sending the bass range to the subwoofer: 40, 60, 80, 100, 120, 150, 200 (Hz)
Factory setting: 80 (Hz)
4. To finish the setting (➔ page 36)
Note
•The setting made through these steps applies to all speakers set as “SMALL ”.
Changing auto speaker settings
To return speakers to factory settings
You can return settings made with the setup microphone to factory settings. (The “AUTO SPEAKER SETUP” indicator goes off when you perform this operation.)
1.To enter the SETUP (➔ page 36)
2.Press [e][r] to select “AUTO SETUP ”, and press [OK] to confirm.
3.Press [e][r] to select “DEFAULT ”, and press [OK] to confirm.
4.Press [e][r] to select “YES ”, and press
[OK] to confirm.
YES : For returning to factory settings
NO : For keeping auto settings
Factory setting: NO
•To cancel, select “NO ”.
5.To finish the setting (➔ page 36)
Setting the unit against automatic polarity adjustment
The unit judges polarity of certain properly connected speakers as opposite. When this happens, set the unit against automatic polarity adjustment and prevent polarity reversal.
1.To enter the SETUP (➔ page 36)
2.Press [e][r] to select “AUTO SETUP ”, and press [OK] to confirm.
3.Press [e][r] to select “POLARITY ”, and press [OK] to confirm.
4.Press [e][r] to select “CHECK NO ”, and
press [OK] to confirm.
CHECK YES : Normal auto speaker setup
CHECK NO : No automatic polarity adjustment
Factory setting: CHECK YES
5. To finish the setting (➔ page 36)
38
Adjusting the
You can adjust the
1.To enter the SETUP (➔ page 36)
2.Press [e][r] to select “AUTO SETUP ”, and press [OK] to confirm.
3.Press [e][r] to select “EQ ADJUST ”, and press [OK] to confirm.
4.Press [e][r] to select the setting, and
press [OK] to confirm.
OFF : For not using a set frequency response.
SOFT :
NORMAL :
HARD :
Factory setting: NORMAL
5. To finish the setting (➔ page 36)
Making bi-wire setting
Make sure to select “YES ” when you connect the unit to bi- wire speakers. The speakers do not produce adequate sounds unless you make this setting.
1.To enter the SETUP (➔ page 36)
2.Press [e][r] to select “LR
3.Press [e][r] to select “YES ”, and press
[OK] to confirm.
YES : When
NO : When
Factory setting: NO
4. To finish the setting (➔ page 36)
Setting the speaker impedance
Make this setting when the speaker impedance is low (4 Ω).
1.To enter the SETUP (➔ page 36)
2.Press [e][r] to select “SPKR IMP ”, and press [OK] to confirm.
3.Press [e][r] to select “4 OHMS ”, and
press [OK] to confirm.
6 OHMS : When the speaker impedance is normal
4 OHMS : When the speaker impedance is low (4 Ω)
Factory setting: 6 OHMS
4. To finish the setting (➔ page 36)
Note
•If at least one speaker among connected speakers has the impedance of 4 Ω, set “4 OHMS ”.
RQT9223