Problem Cause & Solution | Panasonic VL-SW250BX specs

Help

Problem	Cause & Solution			Page
The recorded image quality is	LThe image quality of “8 PICTURES” is lower than “1			37
lower.	PICTURE”. Change the setting of “DOOR STATION PIC REC
	NUMBER” to “1 PICTURE” using the main monitor station if
	higher quality is required.
The recording date and time are	LThe date and time are not set. Set the current date and time			17
not displayed while viewing the	using the main monitor station.
image.
The recorded image taken at	LIt takes some time to display the image from the door station			37
night is dark.	taken at night. Therefore, the auto recording may start before
	the image can be displayed. Change the setting of “PICTURE
	RECORD TIMING” to “DELAYED”.
N Conversation (Doorphone/Intercom)
Problem	Cause & Solution			Page
Sound cuts in/out or fades.	LThe surroundings of the main monitor station, the sub monitor			20
	station or the door station are noisy. Try “Press-to-talk” mode.			―
	LThe antenna on the sub monitor		Antenna	―
	station is being covered with your
	hand. Do not cover it.
	LThe sub monitor station is too far from the main monitor			7, 45
	station. Move closer to the main monitor station. If you install a
	repeater (optional), the sound may be improved.			7, 45
	LThere is an object such as a concrete wall obstructing the			7, 45
	signal. Move to a place without an obstacle. If you install a
	repeater (optional), the sound may be improved.			7
	LA microwave or wireless LAN appliance is in use. Move			7
	closer to the main monitor station or use a sub monitor station
	located away from those appliances. Try again.
A howling noise interrupts the	LA howling noise may occur when you are too close to the other			―
conversation.	party. Move away from the other party.
Your voice cannot be heard by	LWhen	or is displayed, the “Press-to-talk” mode is		20
the outside visitor. (Visitor’s voice	activated. Only while pressing {TALK}, the outside visitor can
can be heard.)	hear your voice.
Voice answer mode does not	LYour voice is not loud enough or your initial reply is too long			18
operate properly.	(must be less than 1 second). Try a different voice volume or
	change the length of your answer until the main monitor station
	or the sub monitor station beeps.
N Ringer tone

Problem	Cause & Solution
The ringer tone for the door	LThe ringer volume is turned off. Turn it on.
station does not sound.	LThe battery is discharged. Charge the battery.

Page

33

16

48

SW250BX_OI.indb 48

2010/08/25 15:58:39

Image 48

Panasonic VL-SW250BX Conversation Doorphone/Intercom Problem Cause & Solution, Ringer tone Problem Cause & Solution

Contents

Attached Installation Guide Thank you for purchasing a Panasonic product Introduction Important InformationPreparation Doorphone Accessory information Product names used in these Operating InstructionsIncluded items VL-SW250BX Additional/replacement accessories Accessory items Order numberWhen using with a lobby station Compatible Panasonic PBXs For your safety Power connectionInstallation Operating safeguards Important safety instructions Installation and relocationBattery Before using For best performanceEnvironment Other information TappingPrivacy and rights of portrait Others Location of controls Door station Main monitor station Press Volume d Monitor display Main monitor stationDisplay during operation Operation guidance Sub monitor station Battery cover Rear view Speaker Charge contacts Metallic parts ChargerCharge contacts Charger stand Monitor display Sub monitor station OFF Back Next LImages on the monitor display Charging the sub monitor station Pad at the backTo assemble the charger stand To remove the charger stand Setting the date and time Volume Voice ChangerVoice Changer Next Answering a call by voice sensor Voice answer mode When using an additional door stationAnswering a call Microphone Features during a call or while monitoring Adjusting the display brightness Main monitor stationAdjusting the speaker volume Main monitor station Main monitor station only Using Door KEY button To speak to the visitorSpeak while pressing and holding Talk To hear the visitor Volume Transferring a callTo transfer a call To receive a transferred call When answering a call Monitor Talk OFFMonitor OFF Talk NTo speak to the other party When installing 2 door stations Press Volume or page , thenMonitoring the outside Door station monitor Monitor NAuto image update Recording an imageAuto recording PLAY/REC Manual recording Press PLAY/RECPress D REC Viewing recorded images using the main monitor station Voice Changer Menu Volume OFFNTo view the next image Voice Changer Back Menu PauseMenu Play Menu Menu Viewing recorded images using the sub monitor station NTo view a series of 8 continuous images Image status Button and guidance Operation Back Volume Menu Protecting the recorded imagesSelect To release protection Press Volume YES Erasing an imageYou can erase unnecessary images Menu OFF Volume Menu OFF Caller ReceiverOFF Talk Adjusting the ringer volume Changing the ringer tone Main monitor station Sub monitor stationRinger tone patterns Sound Sound 1 REPEAT*1 Sound 2 REPEAT*1 Sound 3 REPEAT*1 Setting Door KEY button Press Menu OK, then select Door KEY by pressing Volume orVolume or Press Menu OK, then select the desired item by pressing How to change the function settings Item function SettingFunction list of the main monitor station Time and Date NORMAL, LOW PICTURES, 1 Picture Terminal 2 SIGNALS, 2 Terminals 1 Signal LobbyExternal Device REGISTRATION/CANCELLATION Registration Cancellation Demo Mode Ring Volume Door HIGH, MEDIUM, LOW, OFF Function list of the sub monitor stationStation Init Settings YES, no Voice Answer ON, OFFDisp REC Date ALWAYS, 3 SEC Contrast Expanding your system with optional units Sub monitor station*1 Door station*1 Main monitor station Units required to be installed Adding a door station Using with Panasonic PBXOperating the door opener Please use only a Panasonic PBX Using the main monitor station Using the sub monitor stationTo register a canceled sub monitor station page 46 again Adding a sub monitor station Registration Setting a repeater Registration To power outlet 100 240 V ACStatus indicator Program Canceling registration of the sub monitor station/repeater Cancellation Troubleshooting Monitor display Problem Cause & SolutionAway from those appliances. Try again Problem Cause & Solution Conversation Doorphone/Intercom Problem Cause & SolutionRinger tone Problem Cause & Solution Sub monitor station/Battery Problem Cause & Solution Others Problem Cause & SolutionRemove the battery and insert it again Help Error messages Sub monitor station only Problem Cause & Solution Cleaning Battery replacement Speciﬁcations Main monitor station VL-MW250BXSub monitor station VL-W605BX Door station VL-V566BX Function Settings Lring Volume Lring ToneLvoice Answer Lvoice Changer Lplay Lamp Flashing Lcontrast Lregistration Loutgoing VOL For your future reference Attach your sales receipt here