Others Problem Cause & Solution | Panasonic VL-SW250BX guide

		Help
N Sub monitor station/Battery

Problem	Cause & Solution	Page
ﬂashes and 2 short beeps	LThe battery level is low. Charge the battery immediately.	16
sound.

Even if you place the sub monitor	LThe AC adaptor is disconnected from the power outlet or	16
station on the charger, the	the charger. Plug the AC adaptor into the power outlet or the
CHARGE indicator does not light	charger ﬁrmly.
up.	LThe sub monitor station is not placed on the charger correctly.	16
	Replace it securely. (A short beep sounds and the CHARGE
	indictor lights in solid red.)	52
	LThe charge contacts are dirty. Clean them with a soft, dry cloth.	52
	LThe battery is new or discharged. Place the sub monitor station	16
	on the charger and wait for a few minutes.

The CHARGE indicator does not	LWhen the power of the main monitor station is turned off or	16
go off after the battery has been	“OUT OF RANGE” is displayed on the sub monitor station, the
charged for about 7 hours.	charging time will become longer. Make sure the power of the
	main monitor station is turned on, and charge the sub monitor
	station in a location near the main monitor station where “OUT
	OF RANGE” disappears.

Even if the sub monitor station	LThe battery is at the end of its life. Replace the battery with a	52
has been charged, ﬂashes	new one.
after using it a few times.

The sub monitor station, the AC	LThis is normal. (It may feel a little warmer in summer than in	―
adaptor, or the charger is warm.	winter.) If it feels very hot, disconnect the AC adapter from the
	power outlet and contact our service personnel.

N Others

Problem	Cause & Solution	Page
The main monitor station, the	LThe unit does not work during a power failure. The date and	17
sub monitor station, and the	time may be reset to the default setting after a power failure. In
door station do not work during a	this case, set the date and time using the main monitor station
power failure.	again.

L“DEMO MODE” is displayed.	LDemo mode is activated. Change the setting to “OFF”.	39
LYou cannot answer the call or
make an intercom call.

LThe unit does not work with	LPerform the following operation (Reset).
correct operations.	Main monitor station:	10
LThe unit does not work properly.	Press the RESET switch on the bottom of the main monitor	10
	station with a pointed object. (Recorded images and the
	program settings are not affected.)
	Sub monitor station:	―
	Remove the battery and insert it again.	―
	– Program settings are not affected.
	– is displayed. However, the actual battery level is
	maintained.

49

SW250BX_OI.indb 49

2010/08/25 15:58:39

Image 49

Panasonic VL-SW250BX Sub monitor station/Battery Problem Cause & Solution, Others Problem Cause & Solution

Contents

Thank you for purchasing a Panasonic product Attached Installation Guide Important Information IntroductionPreparation Doorphone Product names used in these Operating Instructions Accessory informationIncluded items VL-SW250BX Accessory items Order number Additional/replacement accessoriesWhen using with a lobby station Compatible Panasonic PBXs Power connection For your safetyInstallation Operating safeguards Installation and relocation Important safety instructionsBattery For best performance Before usingEnvironment Tapping Other informationPrivacy and rights of portrait Others Door station Location of controls Main monitor station Monitor display Main monitor station Press Volume dDisplay during operation Operation guidance Sub monitor station Rear view Speaker Charge contacts Metallic parts Charger Battery coverCharge contacts Charger stand OFF Monitor display Sub monitor station LImages on the monitor display Back Next Pad at the back Charging the sub monitor stationTo assemble the charger stand To remove the charger stand Volume Voice Changer Setting the date and timeVoice Changer Next When using an additional door station Answering a call by voice sensor Voice answer modeAnswering a call Microphone Adjusting the display brightness Main monitor station Features during a call or while monitoringAdjusting the speaker volume Main monitor station Main monitor station only To speak to the visitor Using Door KEY buttonSpeak while pressing and holding Talk To hear the visitor Transferring a call VolumeTo transfer a call To receive a transferred call Monitor Talk OFF When answering a callMonitor OFF Talk NTo speak to the other party Press Volume or page , then When installing 2 door stationsMonitoring the outside Door station monitor Monitor Recording an image NAuto image updateAuto recording PLAY/REC Press PLAY/REC Manual recordingPress D REC Voice Changer Menu Volume OFF Viewing recorded images using the main monitor stationNTo view the next image Menu Pause Voice Changer BackMenu Play Menu Menu NTo view a series of 8 continuous images Viewing recorded images using the sub monitor station Button and guidance Operation Back Image status Protecting the recorded images Volume MenuSelect To release protection Erasing an image Press Volume YESYou can erase unnecessary images Menu OFF Caller Receiver Volume Menu OFFOFF Talk Adjusting the ringer volume Main monitor station Sub monitor station Changing the ringer toneRinger tone patterns Sound Sound 1 REPEAT*1 Sound 2 REPEAT*1 Sound 3 REPEAT*1 Press Menu OK, then select Door KEY by pressing Volume or Setting Door KEY buttonVolume or Press Menu OK, then select the desired item by pressing Item function Setting How to change the function settingsFunction list of the main monitor station Time and Date PICTURES, 1 Picture NORMAL, LOW Lobby Terminal 2 SIGNALS, 2 Terminals 1 SignalExternal Device Demo Mode REGISTRATION/CANCELLATION Registration Cancellation Function list of the sub monitor station Ring Volume Door HIGH, MEDIUM, LOW, OFFStation Voice Answer ON, OFF Init Settings YES, noDisp REC Date ALWAYS, 3 SEC Contrast Sub monitor station*1 Door station*1 Main monitor station Expanding your system with optional units Using with Panasonic PBX Units required to be installed Adding a door stationOperating the door opener Please use only a Panasonic PBX Using the sub monitor station Using the main monitor stationTo register a canceled sub monitor station page 46 again Adding a sub monitor station Registration To power outlet 100 240 V AC Setting a repeater RegistrationStatus indicator Program Cancellation Canceling registration of the sub monitor station/repeater Monitor display Problem Cause & Solution TroubleshootingAway from those appliances. Try again Conversation Doorphone/Intercom Problem Cause & Solution Problem Cause & SolutionRinger tone Problem Cause & Solution Others Problem Cause & Solution Sub monitor station/Battery Problem Cause & SolutionRemove the battery and insert it again Help Sub monitor station only Problem Cause & Solution Error messages Battery replacement Cleaning Main monitor station VL-MW250BX SpeciﬁcationsSub monitor station VL-W605BX Door station VL-V566BX Lring Volume Lring Tone Function SettingsLvoice Answer Lvoice Changer Lplay Lamp Flashing Lcontrast Lregistration Loutgoing VOL Attach your sales receipt here For your future reference