Patton electronic 4020 Series specs

SmartLink 4020 Getting Started Guide	2 • SmartLink installation

Note The SmartLink has automatic MDX (auto-crossover) detection and conﬁgu- ration on all Ethernet ports. Any of the ports can be connected to a host or hub/switch with a straight-through wired cable.

5Connect to the Internet service provider.

The external router power supply automatically adjusts to accept an input voltage from 100 to 240 VAC (50/60 Hz).

Verify that the proper voltage is present before plugging the CAUTION power cord into the receptacle. Failure to do so could result in

equipment damage.

6Verify that the AC power cord included with your router is compatible with local standards. If it is not, refer to “Contacting Patton for assistance” on page 86 to ﬁnd out how to replace it with a compatible power cord. Plug the power adapter into the 12V DC, 1.0A port on the SmartLink 4020. Connect the other end of the power cord to an appropriate AC power outlet.

7Wait 30 seconds after powering the SmartLink 4020 on, then verify that the green Power LED is lit (see ﬁgure 3). At this point, you should be able to use your browser to surf the Internet.

Note Follow the directions of your voice service provider to set up voice services.

Figure 3. Router front panel LEDs

Installing the router

23

Image 23

Patton electronic 4020 Series manual Connect to the Internet service provider

Contents

SmartLink Mailsupport@patton.com Summary Table of Contents Table of Contents Vlan Network-LAN Telephony None System Table of Contents Documentation Calling Features List of Figures List of Figures List of Tables Structure About this guideAudience Safety when working with electricity Precautions General conventions Typographical conventions used in this documentGeneral observations General information Chapter contents SmartLink SmartLink 4020 overview SmartLink installation Do the following Installing the router Connect to the Internet service provider System information System Uptime Home LAN IP Address System informationSystem Uptime WAN IP Address System Status Network-WAN WAN Priority Tag Ieee 802.1q Interface Status Network SettingsStatus Settings Specify ﬁxed WAN conﬁguration Device Operating ModeInternet Conﬁguration Obtain WAN conﬁguration dynamically WAN PPPoE Conﬁguration Enable PPPoEAuthentication Settings WAN MAC Address Spoofed Conﬁguring Dynamic DNSMAC Spooﬁng Conﬁguration Saving your work MTU SizeWAN Vlan Conﬁguration Assured Bandwidth for Voice QoS Quality of ServiceEnable Voice QoS ToS/DiffServ IPSec Conﬁguration Inbound AH Authentication Algorithm Outbound AH Authentication AlgorithmOutbound AH Authentication Key HEX Outbound ESP Authentication Key HEX Inbound ESP Authentication Key HEX Network-LAN Dhcp Viewing the Dchp Client Table Server SettingsClient Network Information Static Address Assignment Viewing the Routing Table RoutingDynamic Routing Static Routing Port Forwarding to LAN Port ForwardingIP Filtering Reserved Ports Filter IP Range Telephony Telephony Telephony Phone Line Status VoIP StatusVoIP Server Registration Status Messages waiting Caller ID SettingUser Name Subscribed for Voicemail SIP Conﬁguration SIP Server SettingsGateway Settings VoIP Vlan Conﬁguration SIP ExtensionsRTP Telephone Event Conﬁguration RTP Parameters SIP Timer Values millisecondsSIP Parameters Hook Flash Mime Type NAT Traversal Jitter Buffer Audio/CODEC ConﬁgurationPacketization FAX without T.38 Use G.711 fax Phone 1 & Phone User Information Supplementary Service Activation Three-Way Conferencing Message Waiting IndicatorCall Forward All Selective Call Forward Dial Out Type Selective Call Forward Settings Call Forward Settings Outgoing Call Block Http Digest SettingIncoming Call Block Block Caller ID Speed Dial Serv Line 1 Speed Dial SettingsLine 2 Speed Dial Settings Speed Dial System System System Web Page Protect Set Security PasswordNew Root Password New User Password Logging Conﬁrm new passwordEnable Syslog Conﬁguration Saving your work Enable DebugDebug Server Debug Connect Port Localization Service AccessEnable Http Enable Ping Reply Conﬁrm Tone Call Progress TonesDial Tone Prompt Tone Off Hook Warning Distinctive Ring SettingBusy Tone Ring Back Tone Name Value Supplementary Service Keys IP Dialing Call forward selectiveBlock Anonymous Calls Warm Line Calling Preﬁx Keys Speed DialingIncome Caller ID Call Conference Voicemail accessCall Hold Call Waiting call alternative Control Timer Values FXS Port Ring Setting Snmp Trap Conﬁguration Snmp ConﬁgurationFXS Port Polarity Conﬁguration Snmp System Conﬁguration Auto UpgradeRoutine Upgrade every xxx days Snmp Community Conﬁguration Upgrade Server Manual UpgradeEnable Auto Upgrade Auto Upgrade Protocol Reload Documentation Documentation link Introduction Logout Logout window Logout Contacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information RMA numbers Out-of-warranty serviceReturns for credit Return for credit policy Appendix a Compliance information CE notice Declaration of Conformity Safety ComplianceCompliance Radio and TV Interference Appendix B Speciﬁcations Fax and Modem Support Voice Processing signalling dependentVoice Connectivity Connectivity Operating Environment Voice Services/FeaturesIP Services Management Appendix C Dial plans Complex Dial Plan Sample Dial PlansSimple Dial Plan Non-dialed Line Dial Plan Sample Dial Plans Appendix D Calling Features Distinctive on Distinctive OFF