Manuals / Patton electronic / Computer Equipment / Network Card

Patton electronic Model 3088/I Ethernet LEDs, 100M Yellow, Link Yellow, Tx Yellow, Rx Yellow

Models: Model 3088/I

1 61

Page 35

3088/I Getting Started Guide	5 • Installation & operation

Ethernet LEDs

There are four Ethernet LEDs: Link, 100M, Tx, and Rx.

Link (Yellow)

The Link LED glows solid when it receives a valid signal on the Ethernet port. If it is not ﬂashing, change the position of the MDI-X switch on the rear panel. If the LED still fails to light, your cable may be faulty.

100M (Yellow)

The Link LED glows solid if the 100Mbps Ethernet link has been negotiated. If there is not Ethernet connec- tion, the LED defaults to on to indicate that the Ethernet port is ready to operate in 100Base-TX mode.

Tx (Yellow)

The Link LED ﬂashes upon transmitting data out the Ethernet port.

Rx (Yellow)

The Link LED ﬂashes when receiving data from the Ethernet port.

LED status indicators

Page 35

Image 35

Patton electronic Model 3088/I manual Ethernet LEDs, 100M Yellow, Link Yellow, Tx Yellow, Rx Yellow

Contents

Sales Ofﬁce +1 301 Model 3088/IRocketLink-G G.SHDSL NTU Getting Started Guide7622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Summary Table of Contents Initial configuration Table of ContentsSummary Table of Contents Table of ContentsSystem Management Installation & operationDiagnostic tools Table of ContentsCompliance information RS-232 console interface pin assignments Table of ContentsRJ-45 shielded 10/100 Ethernet port F RS-232 console interface pin assignmentsList of Figures 1 General conventions List of TablesStructure About this guideAudience Note A note presents additional information or interesting sidelights Precautionsimpaired functioning Place the unit on a ﬂat surface and ensure free air circulation Safety when working with electricityGeneral observations Clean the case with a soft slightly moist anti-static clothGeneral conventions Typographical conventions used in this documentChapter 1 General information Chapter contentsRocketLink-G 3088/I overview FeaturesChapter contents Chapter 2 Initial conﬁgurationIntroduction Power up the NTUAC power-up DC power-upConnect a PC and log in Power-up indicationConﬁgure the IP address WARNING ton for assistance” on pageConnect to the local IP network Modify the IP addressConnect the G.SHDSL port Log onto the web management interfacesee ﬁgure Ethernet Console PowerFigure 7. Rear view of 3088/I showing DSL RJ-11 jack LineChapter contents Chapter 3 G.SHDSL conﬁg and statusDSL Parameters DSL conﬁgurationDSL Error Monitor Conﬁguration Run-Time Statistics Loss Of Signal Indicates Signal Loss or Signal FoundG.SHDSL Status Local Interface Error Counters DSL Line Error CountersG.SHDSL Status Clearing Error CountersFigure 13. Clearing the error counters 3 G.SHDSL config and statusChapter contents Chapter 4 Ethernet & WAN PPPconﬁg and status Ethernet Basic Port Attributes IP conﬁgurationPPP conﬁguration Ethernet port conﬁgurationFigure 17. Top of web page for conﬁgurable Ethernet parameters Ethernet Advanced Port AttributesFigure 16. Ethernet performance statistics Figure 18. Conﬁgurable Ethernet parameters 4 Ethernet & WAN PPP config and statusEthernet port configuration Chapter contents Chapter 5 Installation & operationOperation InstallationPower-up Connecting the twisted-pair interfaceLink Yellow LED status indicatorsPower Yellow WAN LEDsTx Yellow Ethernet LEDs100M Yellow Link YellowChapter contents Chapter 6 System ManagementFigure 20. Typical RocketLink Plug ‘n’ Play Application RocketLink-G Plug ‘n’ PlayConsole Reset for Factory DefaultSaving the conﬁguration Figure 23. Backing up and reloaded saved conﬁgurations AuthenticationBacking up and restoring saved conﬁgurations Figure 24. Login AuthorizationFigure 25. Upgrading software on the 3088/I System Software UpgradeFigure 26. Software upgrade protection Chapter contents Chapter 7 Diagnostic toolsPing & Traceroute System tools for testingClearing error counters LED status monitor & deﬁnitionChapter contents Chapter 8 Contacting Patton for assistancePatton support headquarters in the USA Warranty Service and Returned Merchandise Authorizations RMAsWarranty coverage Contact informationRMA numbers Out-of-warranty serviceReturns for credit Return for credit policyChapter contents Appendix A Compliance informationRadio and TV Interference FCC Part SafetyCompliance FCC Part 68 ACTA StatementAuthorized European Representative Industry Canada NoticeCE Declaration of Conformity Chapter contents Appendix B SpeciﬁcationsProtocol support General characteristicsG.SHDSL characteristics EthernetManagement Serial connectorDiagnostics PowerEthernet Tx Power48 VDC power supply Ethernet 100MG.SHDSL Physical connection & Transmission Line DimensionsLine Interface EnvironmentChapter contents Appendix C Factory replacement parts and accessoriesAmerican Power Cord “K” Factory replacement parts and accessoriesEuropean Power Cord CEE 7 “A” United Kingdom Power Cord “D”RJ-11 non-shielded DSL port Appendix D RJ-11 non-shielded DSL portChapter contents 2 Tip 3 Ring RJ-11 non-shielded DSL portSignal Pin #RJ-45 shielded 10/100 Ethernet port Appendix E RJ-45 shielded 10/100 Ethernet portChapter contents 1 TX+ output 2 TX- output 3 RX+ input RJ-45 shielded 10/100 Ethernet portSignal Pin #RS-232 console interface pin assignments Appendix F RS-232 console interface pin assignmentsChapter contents CD out RS-232 console interface pin assignmentsSignal Signal Ground