Preset 95 Accessing Main Menu | Pelco C3463M-B instruction

PRESET 95: ACCESSING MAIN MENU

You can call up the main menu on your monitor by configuring (setting or creating) preset 95 (preset 28 in AD-32 preset mode).

Configuring preset 95 for Pelco’s controllers varies according to the type of controller you are using. Instructions for configuring preset 95 are given below for various Pelco controllers.

CM6700/CM6800

1.Enter the number of the Spectra IV dome system and press the CAM key.

2.Enter 95 and hold the PRESET key for two seconds.

3.In the Edit Preset menu, go to SET and press the ACK key. The main menu appears.

KBD200A/KBD300A: Direct Mode Only

1.Enter 95.

2.Hold the PRESET key (approximately five seconds) until the main menu appears on the screen.

CM9500

1.Enter the number of the Spectra IV dome system and press the CAM key. The main menu appears.

2.Highlight SETUP in the main menu and press the SELECT key.

3.Highlight CAM in the Setup menu and press the SELECT key.

4.Highlight PRESET in the Camera menu and press the SELECT key.

5.Enter 95 and press the F1 key. The main menu appears.

CM9740/CM9760/CM9770/CM9780

1.Press the ESCAPE key to open the main menu. Select DEF. The Define submenu appears.

2.Enter your four-digit PIN if this is your first time entering this mode.

3.Enter 95 and select PRST. The main menu appears.

4.Select the Quit icon to return to the default menu.

KBD4000/KBD4002

1.Press the SPOT MONITOR key.

2.Enter 95, then hold the PRESET key (approximately five seconds) until the main menu appears on the screen.

MPT9500

Extended Coaxitron or RS-485 Mode

1.Enter 95 and press the PRESET SET key.

2.Press the F2 key. The main menu appears.

NET300/NET350/NET4001A

1.Check the Set box.

2.Click the preset 95 button. The main menu appears.

C3463M-B (2/11)

11

Image 11

Pelco C3463M-B manual Preset 95 Accessing Main Menu, Extended Coaxitron or RS-485 Mode

Contents

Spectra IV SL and Spectra IV SE Series Page Contents Field Align Page Description Switch Settings Installation SW2 Switches 6 to 8 Baud Settings SW2 Switches 4 and 5 Serial Port Settings Address Dome Drive Quick Operation Guide Quick Configuration GuideOperation Extended Coaxitron or RS-485 Mode Preset 95 Accessing Main Menu Digital Sentry DS Controlpoint Endura WorkstationDigital Sentry System Software 23X LowLight Day/Night Menu Tree Password Edit the Password Dome SettingsLine Sync Presets Alarms Patterns Zones Alert Current Reading Clear Password27X LowLight Day/Night Menu Tree Label Position Event Edit Event Power UP Line Sync Presets Motion Detection 35X LowLight Day/Night Menu Tree Azimuth Elevation Zoom Custom Camera Settings Spectra Language Reset Camera Cycle Camera Power Reboot System ExitLanguage System Information DIP Switch Information Restore Factory Defaults Back Exit Display SetupExit Display Setup Preset Label Alert Message Title Text Save and Exit Cancel HelpLabel Positions Event Auto Focus Dome SettingsCamera Type of Lighting PT Focus Lock Zoom LimitZoom Speed LOW Light Limit Low Light Focus IR CUT FilterAuto IR Level Auto Iris Advanced Camera SettingsShutter Speed AGC Limit Electronic Image Stabilization Auto SharpnessAuto White Balance Backlight Compensation Field Align OFF Low lux noise reduction is disabledLOW LUX Noise Reduction Video Level Auto Flip Motion SettingsLOW Light Sharpness Minimum Focus Distance Limit Stops Preset Freeze FramePark Time Scan Speed Auto Tracking Power UP Start Time Line Sync Zoom Presets Lost ActionAuto Tracking Azimuth Zero Zoom Display SetupSensitivity Start Time Back Exit Power UP Power UP Action Power UPPower UP Action Back Exit Presets Preset Number PresetsTable C. Stored Presets by Back Box Model Back Exit Line Sync Line Sync Phase Preset 96 Stop a scan Preset 83 to 87 ReservedPreset 92 to 93 Scan limit stops Preset 94 Reserved Preset 95 Select main configuration menu Space Label for Preset Preset NumberAbcdefghij Cancel Klmnopqrst Uvwxyz Edit Detection Areas Enable Motion DetectionMotion Detection Aux Time Activate Aux CommandEdit Schedule Back Exit PatternsBack Exit Patterns Clear Zone Back Exit ZonesBack Exit Zones Zone Number Edit Zone Label To set a window blanking area Enable Window Reverse Clear Window Back ExitWindow Blanking Clear Window DisabledReverse Blanked Area Blank ALL ABOVE/BLANK ALL belowBlank All Above Blank All Below Alarms C3463M-B 2/11 Dwell Time Secs Edit Schedule Back Exit Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 ModeAUX Edit Title Text Title TextBack Exit Title Text System Condition Alert Message AlertRepeat ACK Action Current Reading Reset AlertNone default Not activated Activate AUX Back Abcdefghij Cancel Klmnopqrst Exit Uvwxyz PasswordBack Exit Password Enable Password Edit Password Clock Follow the instructions in for Fixed DATE, adding Week Holiday EventEvent Type Back Exit Event Event Type Event Label Edit Event Event LabelEdit Event Label Edit Holiday Clear EventList Event Holiday Month January DAY Back Exit Clear HolidayList Holidays Edit Holiday Occurrence Use this page to record scheduled events Example Preset Weekend 1100 AM Sat-SunScheduled Events Reboot System Reset, Cycle Power, RebootReset Camera Cycle Camera Power Software/Language File Upload Maintenance Zoom Speed 4.2/5.8 seconds Horizontal Angle of View SpecificationsSignal Format 23X Models DD427 27X Models DD4CBW35 35X Models Appendix Table F. Switch Settings for SW1 Pelco P-Type Control Spectra Switch Setting Address Table G. Switch Settings for SW1 Pelco D-Type Control 1 Table G. Switch Settings for SW1 Pelco D-Type Control 2 Table G. Switch Settings for SW1 Pelco D-Type Control 3 Table G. Switch Settings for SW1 Pelco D-Type Control 4 Table G. Switch Settings for SW1 Pelco D-Type Control 5 Table G. Switch Settings for SW1 Pelco D-Type Control 6 Product Warranty and Return Information