Auto Tracking, Azimuth Zero | Pelco C3463M-B instruction

To set manual or scan stops:

1.Use the joystick to position the cursor beside SET MANUAL STOPS or SET SCAN STOPS.

2.Press Iris Open.

3.Follow the directions displayed on the monitor.

NOTE: In order for the manual or scan stops to work, the LIMIT STOPS option must be ON.

To clear manual or scan stops:

1.Use the joystick to position the cursor beside CLEAR MANUAL STOPS or CLEAR SCAN STOPS.

2.Press Iris Open.

3.Follow the directions displayed on the monitor.

AZIMUTH ZERO

Azimuth is the pan angle from zero to 359 degrees. Azimuth zero is the pan position you specify to be the zero degree point. Azimuth zero is normally set to magnetic north. Once set, azimuth and compass readings are based on the set Azimuth Zero point.

To configure azimuth zero:

1.Use the joystick to position the cursor beside SET AZIMUTH ZERO.

2.Press Iris Open.

3.Follow the directions displayed on the monitor.

To clear azimuth zero:

1.Use the joystick to position the cursor beside CLEAR AZIMUTH ZERO.

2.Press Iris Open.

3.Follow the directions displayed on the monitor.

AUTO TRACKING

(Applies to 27X and 35X models only.)

SPECTRA IV

LANGUAGE

<SYSTEM INFORMATION> <DISPLAY SETUP> <DOME SETTINGS> ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER REBOOT SYSTEM

EXIT


DOME SETTINGS				AUTO TRACKING
<CAMERA>				AUTO TRACKING	OFF
<MOTION>				DISPLAY SETUP	ON
<AUTO TRACKING>				SENSITIVITY	HIGH
<POWER UP>				START TIME	60
<LINE SYNC>				ZOOM	ON
<LINE SYNC>				ZOOM	ON
<PRESETS>				LOST ACTION	STOP
<PATTERNS>				RETURN	OFF
<ZONES>
<WINDOW BLANKING>
<ALARMS>
<AUX>
<TITLE TEXT>
<ALERT>*
<CLEAR>
<PASSWORD>
<CLOCK>
<EVENT>
BACK
EXIT

AUTO TRACKING

Auto tracking allows the camera to automatically pan, tilt, and zoom to track objects of interest (people, cars, and so forth) when motion is detected in a scene without requiring an operator to manually control the camera’s PTZ movements. There are two settings:

ON: Auto tracking is enabled.

OFF (default): Auto tracking is disabled.

NOTE: If the auto tracking setting is OFF, all other settings in the Auto Tracking menu are disabled.

C3463M-B (2/11)

31

Image 31

Pelco C3463M-B manual Auto Tracking, Azimuth Zero, Power UP Start Time Line Sync Zoom Presets Lost Action

Contents

Spectra IV SL and Spectra IV SE Series Page Contents Field Align Page Description Switch Settings Installation SW2 Switches 6 to 8 Baud Settings SW2 Switches 4 and 5 Serial Port Settings Address Dome Drive Operation Quick Configuration GuideQuick Operation Guide Extended Coaxitron or RS-485 Mode Preset 95 Accessing Main Menu Digital Sentry System Software Endura WorkstationDigital Sentry DS Controlpoint 23X LowLight Day/Night Menu Tree Password Edit the Password Dome SettingsLine Sync Presets Alarms Patterns Zones Alert Current Reading Clear Password27X LowLight Day/Night Menu Tree Label Position Event Edit Event Power UP Line Sync Presets Motion Detection 35X LowLight Day/Night Menu Tree Azimuth Elevation Zoom Custom Camera Settings Language Reset Camera Cycle Camera Power Reboot System ExitSpectra Language System Information DIP Switch Information Exit Display Setup Preset Label Display SetupRestore Factory Defaults Back Exit Alert Message Title Text Save and Exit Cancel HelpLabel Positions Event Auto Focus Dome SettingsCamera Type of Lighting PT Focus Lock Zoom LimitZoom Speed LOW Light Limit Auto IR Level IR CUT FilterLow Light Focus Auto Iris Advanced Camera SettingsShutter Speed AGC Limit Electronic Image Stabilization Auto SharpnessAuto White Balance Backlight Compensation Field Align OFF Low lux noise reduction is disabledLOW LUX Noise Reduction Video Level Auto Flip Motion SettingsLOW Light Sharpness Minimum Focus Distance Limit Stops Preset Freeze FramePark Time Scan Speed Auto Tracking Power UP Start Time Line Sync Zoom Presets Lost ActionAuto Tracking Azimuth Zero Zoom Display SetupSensitivity Start Time Power UP Action Power UPBack Exit Power UP Power UP Action Back Exit Presets Preset Number PresetsTable C. Stored Presets by Back Box Model Back Exit Line Sync Line Sync Phase Preset 96 Stop a scan Preset 83 to 87 ReservedPreset 92 to 93 Scan limit stops Preset 94 Reserved Preset 95 Select main configuration menu Abcdefghij Cancel Klmnopqrst Uvwxyz Label for Preset Preset NumberSpace Motion Detection Enable Motion DetectionEdit Detection Areas Edit Schedule Activate Aux CommandAux Time Back Exit Patterns PatternsBack Exit Clear Zone Back Exit ZonesBack Exit Zones Zone Number Edit Zone Label Window Blanking Enable Window Reverse Clear Window Back ExitTo set a window blanking area Reverse DisabledClear Window Blank All Above Blank All Below Blank ALL ABOVE/BLANK ALL belowBlanked Area Alarms C3463M-B 2/11 AUX Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 ModeDwell Time Secs Edit Schedule Back Exit Back Exit Title Text Title TextEdit Title Text System Condition Alert Message AlertRepeat ACK Action Current Reading Reset AlertNone default Not activated Activate AUX Back Abcdefghij Cancel Klmnopqrst Exit Uvwxyz PasswordBack Exit Password Enable Password Edit Password Clock Follow the instructions in for Fixed DATE, adding Week Holiday EventEvent Type Back Exit Event Event Type Event Label Edit Event Label Event LabelEdit Event Edit Holiday Clear EventList Event Holiday Month January DAY Back Exit Clear HolidayList Holidays Edit Holiday Occurrence Scheduled Events Example Preset Weekend 1100 AM Sat-SunUse this page to record scheduled events Reboot System Reset, Cycle Power, RebootReset Camera Cycle Camera Power Software/Language File Upload Maintenance Zoom Speed 4.2/5.8 seconds Horizontal Angle of View SpecificationsSignal Format 23X Models DD427 27X Models DD4CBW35 35X Models Appendix Table F. Switch Settings for SW1 Pelco P-Type Control Spectra Switch Setting Address Table G. Switch Settings for SW1 Pelco D-Type Control 1 Table G. Switch Settings for SW1 Pelco D-Type Control 2 Table G. Switch Settings for SW1 Pelco D-Type Control 3 Table G. Switch Settings for SW1 Pelco D-Type Control 4 Table G. Switch Settings for SW1 Pelco D-Type Control 5 Table G. Switch Settings for SW1 Pelco D-Type Control 6 Product Warranty and Return Information