Pentair SunTouch - page 8

vi

SunTouch Pool and Spa Control System Installation and User’s Guide

Technical Support

Sanford, North Carolina (8 A.M. to 5 P.M. ET)

Moorpark, California (8 A.M. to 5 P.M. PT)

Phone: (800) 831-7133

Fax: (800) 284-4151

Web sites

visit www.pentairpool.com and staritepool.com

Contents

Main Page i ii iii iv IMPORTANT SAFETY PRECAUTIONS Important Notice: IMPOR T ANT SAFETY PRECA UTIONS General Installation Information Safety Notice Page Section 1 SunTouch System Overview SunTouch Control System Overview SunTouch Solar Mode Page Control Buttons 4 SunTouch Main Status Screen (Solar Only) The SunTouch Solar Only main status screen display description is given below. 11:51 AM SOL ON 11:51 AM Operating SunTouch in Solar Only Mode Setting up SunTouch for Solar Only mode from Pool/Spa mode Solar Only Menus Solar Only Menus The SunTouch Solar Only mode menus are shown below: Page Solar Only Menus to start and stop solar water heating. Freeze Protection in Solar Only mode Operating SunTouch in Pool/Spa mode (Shared Equipment) Setting up SunTouch to Operate in Pool/Spa Mode Adjusting the water temperature setting in Pool/Spa mode Adjusting the water temperature setting in P ool/Spa mode Selecting the heat source To select the heat source: SunT ouch Main Status Screen 11:51AM HEATER Pool/Spa Mode Menus (Shared Equipment) Pool/Spa Mode Menus Circuit On/Off Menu (1/13) Circuit On/Off Menu (1/13) Heat Menu (2/13) Heat Menu (2/13) Delay Cancel Menu (3/13) Schedules Menu (4/13) Schedules Menu (4/13) Clock Menu (5/13) Solar Menu (6/13) Valves Menu (7/13) Advanced Menu (8/13): Pool/Spa Delays Advanced Menu (8/13): Temp Units - F / C (Fahrenheit/Celsius) Advanced Menu (8/13): Calibrate water, air and solar sensors Advanced Menu (8/13): Air Sensor Advanced Menu (8/13): System Mode Advanced Menu (8/13): System Type Advanced Menu (8/13): Reset Factory Diagnostics Menu (9/13): Firmware Rev Diagnostics Menu: Solar Temp Diagnostics Menu: Self Test Circuit Functions Menu (10/13) Assigning Circuit Functions Freeze Protection Circuit Functions Menu (10/13) Preset Circuit Functions Settings Menu (11/13): QuickTouch (QT4) Wireless Remote Pump Menu (12/13) Pump Menu (12/13) IntelliFlo Freeze Protection IntelliChlor Menu (13/13) IntelliChlor Menu (13/13): Status and Error Messages SunTouch Main Status Screen (Pool/Spa Mode - Single Body System) 11:51AM HEATER High/Low Temperature Circuit Control (Single Body System) HI-TEMP / LO-TEMP Circuit Control Pool/Spa Mode (Single Body of Water) Menus For menu descriptions, see The Pool/Spa Mode Menus on page 13. Page Section 2 Installation and Setup SunTouch System Installation Steps Summary Required Tools SunTouch Solar Package Contents SunTouch Pool/Spa Package Contents SunTouch System Overview 40 SunT ouch P o wer Center SunTouch Power Center (Front View) (14 H x 12 W x 4 D) Plumbing Requirements Equipment Location Solar Hydraulics System SunTouch Power Center High Voltage Connections SunTouch Power Center Location Grounding and Bonding to the SunTouch Power Center Preparing the SunTouch Power Center Mounting the SunTouch Power Center Removing Electrical Conduit Knockouts Installing Conduit and Wire to the SunTouch Power Center Transformer Connections 240 VAC 120 VAC SunTouch Motherboard Connections 120 VAC 120 VAC - CLEANER: BOOSTER CLEANER PUMP (SOLAR ONLY) ONLY AUX VALVE C or SOLAR VALVE ACTUATOR Accessing the SunTouch Motherboard Installing Auxiliary Relays Relay locations Installing relays Installing relays (Continued) Installing Valve Actuators Installing and Connecting Temperature Sensors Water Temperature Sensor Ambient Air Temperature Sensor (for freeze protection) Solar Temperature Sensor Connecting SunTouch to Heaters Connecting to a standard heater Connecting to a Pentair MiniMax, MasterTemp Connecting to a StaRite heater SunTouch Solar System Installation SunTouch Solar System Start-Up Pool Cleaner Protection SunTouch Pool/Spa Controller System Start-Up Check Electronics SunTouch System Test Setting up the SunTouch System for the First Time (after equipment installation) Set the system time for Solar Only and time and date for Pool/Spa mode. Page Section 3 Troubleshooting Troubleshooting Frequently Asked Questions (FAQ) SunTouch Error Messages Problem Solving a Solar System Temperature vs. Resistance Data System Problem Diagnosis Use the following information to resolve system problems. Problem: SunTouch LCD fails to operate. IntelliChlor Error Messages Problem: The Quick Touch remote will not work, or will not work dependably. Problem: The Quick Touch remote will not work, or will not work dependably (Continued). IntelliFlo 4x160 Warning and Alarm Conditions Alarm and warning LED sequence Wiring SunTouch to the InteliiChlor Salt Chlorine Generator SunTouch Specifications Wiring Description (SunTouch to IntelliChlor) Page Appendix Emergency Shut-Off Switch (ESO3) Emergency Shut-Off switch Location 74 Installing the ESO Circuit Board SunTouch Power Center VALVE ACTUATORS SOLAR ONLY Installing the ESO Circuit Board Glossary