Removing/Replacing Lamps | Philips 27964-01A specification

Removing/Replacing Lamps

Care and Maintenance - Lamp and Acrylic Replacement

Removing/Replacing Lamps

After removing the acrylic shield, replace lamps as follows.

Step 1 Grasp the lamp at one end and at the middle and turn the lamp one quarter turn. Gently remove the lamp from its holders.

Step 2 Reinstall the lamp by inserting the pins located on the ends of the lamp into the slots on top of the lamp holders and turn the lamp a quarter turn. It should click in place.

Recommended Replacement Lamps

We recommend using the lamps specified below. Use of uncertified lamps is a viola- tion of Federal regulations and will void your warranty. These lamps have an aver- age life of 800-1000 hours of effective tanning use. Lamps used longer than that begin to lose their effectiveness even though they continue to light.

Recommended Replacement Acrylics

Acrylics vary greatly over time in their ability to effectively transmit UV light. Acrylics sold by ETS have been life tested to ensure proper transmission throughout their useful life.

THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THIS EQUIPMENT:

Velocity® Wolff® Model VEL 71-T12-100W

Heraeus E400 HPT, Philips Model HPA 400/30s or CosmoTech Model 23045 (SolarMax™ IFT facial unit in 30 3F and 32 3F)

27964-01A

22

Image 27

Philips 27964-01A user manual Removing/Replacing Lamps, Recommended Replacement Lamps, Recommended Replacement Acrylics

Contents

27964-01A USER MANUAL ETS, LLC 7445 Company Drive, Indianapolis, IN 24 MONTH “SILVER MEDAL” WARRANTY Care and Maintenance elcomeontents Safety Information Installation Velocity Wolff Model VEL 71-T12-100W afety InformationRECOMMENDED EXPOSURE TIMES IN MINUTES MAXIMUM EXPOSURE TIME IS 20 MINUTES LE TEMPS D’EXPOSITION MAXIMAL EST DE 20 MINUTES Renseignements sur la SécuritéTEMPS D’EXPOSITION RECOMMANDÉ EN MINUTES Velocity Wolff Modèle VEL 71-T12-100W nstallation Unpacking and InspectionTools Required Installation - Pre-Installation Planning Pre-Installation Planning Hardware Inventory Installation - Hardware Inventory Assembly Procedures Installation - Assembly ProceduresLower Clevis Fork Assembly LOCKNUT others hidden STAND UPRIGHT MACHINE SCREWS 27964-01A Stand Upright Assembly Canopy Installation gas springs Install Gas Springs3. Screw the upper clevis forks onto the 1. Have a helper hold the canopy in its Attach Gas Springs Attach Cover Panels Attaching Handle to Canopy body fan sold separately Body Fan AssemblyShock hazard Be sure power is disconnected before installing body fan CENTER INSERT27964 -01A Electrical Connections Installation - Electrical Connections Remote System Hook-up Scenarios T-Max Wireless Remote SystemRemote Connections T-Max Products Scenario 3 - T-Max Manager Series with Wireless combo Installation - Remote ConnectionsScenario 1 - T-Max Manager Series with Complete Wireless Scenario 2 - T-Max 3A with Wireless Scenario 4 - T-Max Manager Series with Wireless combo Scenario 5 - T-Max Manager Series with wiresScenario 6 - Single Bed wired to T-Max 3A Setting the sunbed address manually Setting the “id”1-99 100-199 DANGER perationBefore You Tan Exposure Times Using Your Sunbed Operation - Using Your SunbedA BC D E F G body using the canopy handle. See Safety Cleaning the Canopy and Bench are and MaintenanceCleaning After Use Thorough Periodic Cleaning Lamp and Acrylic Replacement Care and Maintenance - Lamp and Acrylic ReplacementRemoving/Replacing Acrylic Shield Velocity Wolff Model VEL 71-T12-100W Recommended Replacement LampsRecommended Replacement Acrylics Removing/Replacing Lamps DANGER Removing/Replacing Face Tanner Lamp if equipped Clean sunbed, see Thorough Periodic Cleaning ProblemSolution roubleshooting Connections Troubleshooting Remote Connections My bed is connected to a T-Max S-30SV S-32SV S-30SV3F S-32SV3F Parts List 30 3F SUNVISION Elite 32SV32SV3F