OPERATING THE VCR FROM A PERSONAL COMPUTER
Connect this VCR to a personal computer via the
■
Communication rate: | 1200/2400/4800/9600 BAUD (The rate can be specified using the SELECTION MENU | |
| screen. This is set to 9600 BAUD at the factory.) | |
Communication format: | Start: | 1 bit |
| Data: | 8 bits |
| Parity: | None |
| Stop: | 1 bit |
Communication codes: | Two types, the ASCII and display character codes | |
ASCII code |
|
|
|
|
|
|
|
| The codes with diagonal line are not used. | |||||
| 0 1 2 3 4 5 6 7 8 9 A B C D E F | |||||||||||||
0 |
|
| SX | EX |
|
|
|
|
|
|
|
|
|
|
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2 | (blank) | ! |
|
|
|
|
|
|
|
| ✽ | , | – |
|
3 | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | : | < | > | ? |
4 |
| A B C D E F G H I J K L M N O | ||||||||||||
5 | P Q R S T U V W X Y Z |
|
|
| ||||||||||
6 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
7 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Display character code | The codes with diagonal line are not used. |
| 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | A B C D E F | ||||
0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2 | (blank) |
| “ |
| $ | % | & | ’ | ( | ) | ✽ | + | , | / | |
3 | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | : | ; |
| = | ? |
4 |
| A B C D E F G H I J K L | M N O | ||||||||||||
5 | P Q R S | T U V W X Y Z |
|
|
|
| |||||||||
6 |
| a | b | c | d | e | f | g | h | i | j | k | l | m n | o |
7 | p | q | r | s | t | u | v w x | y | z |
|
|
|
| ||
■Communication Protocol
1.Be sure to attach an “SX” code at the start of communications and an “EX” code at the end. The VCR does not accept the command without these codes.
2.The VCR only transmits a reply to the received command.
3.When the VCR receives one of the remote control commands shown on page 25, it returns the status for reception acknowledgment or the status requested currently.
4.If the commands are transmitted consecutively or another command is transmitted before the VCR has ended an operation, the VCR returns the “SX”BUSY”EX” code.
5.If there is a mistake in the received communications format, the VCR returns one of the following commu- nication error codes.
• | ERL: | Error in code length |
• | ERC: | Error in code format |
• | ERT: | Error inside the VCR (when return is not possible within about 2 seconds) |
6.When the VCR detects a communications error such as a stop bit error, bit length error, etc., it replaces the received byte with “!” for processing.
∗If a communications error occurs in the OSD display data, the OSD character is replaced with “!”. If a communications error occurs in data other than the above, a communications error code is returned.
■OSD Display Data
When the date and hour are displayed or nothing is displayed (only the picture is displayed), up to 12 characters are displayed at the position shown in the figure.
Up to 12 characters are displayed at this position.
14 : 30 : 27 09
24
