SETUP
1.CLOCK SET
2.TIMER
3.SELECTION MENU 1
4.SELECTION MENU 2
5.ALARM
6.ALARM MEMORY
Note: If the VCR is not turned on for about 720 hours after the
SELECTING A FUNCTION TO BE PROGRAMMED The program menu will always begin with the CLOCK SET function, followed by the TIMER, SELECTION MENU 1, SELECTION MENU 2, ALARM, and then the ALARM MEMORY functions. Although the program menu always follows this order, it is possible to skip any of the available func-
CLOCK SET
TIMER DISPLAY
SELECTION MENU 1
SELECTION MENU 2
ALARM DISPLAY
ALARM MEMORY DISPLAY
1 |
|
| CLOCK SET |
| ||
|
| |||||
12 | : 00 : A |
|
|
| ||
OSD |
| OPT I ONS |
|
| ||
TYPE : | OFF |
| ||||
T IME | ADJUST : | SLAVE |
| |||
|
|
|
|
|
| |
|
|
|
|
|
|
|
1 | | 12 | : 00A a 12 : | 00A | 06 | |
2 | | 12 | : 00A a 12 : | 00A | 06 | |
3 | | 12 | : 00A a 12 : | 00A | 06 | |
4 | | 12 | : 00A a 12 : | 00A | 06 | |
5 | | 12 | : 00A a 12 : | 00A | 06 | |
6 | | 12 | : 00A a 12 : | 00A | 06 | |
7 | | 12 | : 00A a 12 : | 00A | 06 | |
MON:✽,✽ TUE :✽,✽ WED :✽,✽ | ||||||
THU :✽,✽ FR I :✽,✽ SAT :✽,✽ | ||||||
|
|
| SUN:✽,✽ |
|
| |
|
|
| ||||
| SELECT I ON MENU |
| ||||
SEARCH SPEED : | X5 |
| ||||
ONE SHOT REC : | 6F I ELD |
| ||||
BAUD RATE : | 9600BAUD | |||||
CAMERA | SW : | ALL |
| |||
|
|
|
| |||
|
|
|
| |||
|
| SELECT I ON MENU |
| |||
|
| BUZZER SELECT I ON | ||||
TAPE | END : |
| OFF |
| ||
TROUBLE : |
| OFF |
| |||
NO | V I DEO : |
| OFF |
| ||
AUTO REC CHECK : OFF |
| |||||
ALARM | OUT : |
| OFF |
| ||
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| ALARM SET |
| ||
DURAT I ON: | MANUAL |
| ||||
SPEED : |
| 06 |
|
| ||
ALARM READY : YES |
|
| ||||
ALARM | OUT : | DURAT I ON | ||||
| RECYCLE FUNCT I ONS |
| ||||
REW I ND , STOP | I F | ALARM |
| |||
|
|
|
|
|
|
|
ALARM MEMORY A00
1
2
3
4
5
6
7
8
9
tions during the selection process.
To select the desired program function (and to move from one program function to the next), press the PROGRAM button repeatedly until the desired func- tion display format appears on the monitor.
After the desired function has been selected, follow the corresponding procedure to set that function.
SETTING THE PROGRAM FUNCTION(S)
The first step in each programming procedure is: “Press the START/STOP button”. The system allows up to five minutes for any one function set- ting to be completed after the START/STOP button is pushed. If no change/setting is entered within the five minutes period, the unit will automatically exit the selected program function. (If this happens, re- select the desired program function, and follow the programming procedure for that function.)
The following procedures for setting VCR functions assume that the desired function has already been selected.
Note: During programming, holding the SET, UP, or DOWN button will move/change the displayed infor- mation at a rapid rate.
Initial Program Function Display Formats
13
