Philips manual TTX400 electrical units

TTX400

TTX400 electrical units

These electrical units are designed for quick-click mounting in TTX400 trunking sections.They are for use with one or two TL5 or TL-D lamps, with electronic (dimming) ballast (or conventional ballast in the case of TL-D), and are available in emergency lighting versions and in versions for the mounting of projectors.They contain all the necessary electrical and mechanical functions.All components are screwed onto the electrical unit.The units can be combined with any type of reflector and are made of white sheet steel.

TMX400 is delivered with electronic ballast HFP. The dimmable version of the TMX400 is delivered with the electronic ballast HFR, allowing the light output of the TL5 lamps to be regulated from 3 to 100 %.This

	TTX400 TL5
	Electrical units
Type	TMX400
Light source	Fluorescent:
	1 x or 2 x MASTER TL5 / G5 / 28, 35, 49, 54,
	80 W
Gear	Electronic, 220 - 240 V / 50 - 60 Hz:
	High Frequency Performer (HFP)
	High Frequency Regulator (HFR)
	High Frequency Regulator, DALI and Touch
	(HFR-TD)
Option	Emergency lighting:
	1 hour (EL1), 3 hours (EL3)
	Master/Slave:
	1 master + 1 slave (M/S), both master and slave
	(M-S)
	HFR/HFR-TD with emergency lighting:TMX400 9
	for trunking 9 wires or preferably TMX400 2-CR
	to be used with TTX400 7-wires (thereby in case
	of non-continuous lightline, to order throughwiring
	ZTX400 C1300-2 or C1600-2 as accessory)
Material	Sheet steel, white
Installation	Click-in fixation (both mechanical and electrical
	connection) on trunking TTX400 with 5- or 7-wire
	ribbon cable
Accessory	Blind covers (BC)
	Throughwiring set to be used in combination
	with TMX400 C2R onto TTX400 7, in the case of
	non-continuous lightline (ZTX400 C1300-2 for
	1 section 28/54 W; ZTX400 C1600 for 1 section
	35/49/80 W).

unit is ideal for (day)light-dependent control and must be mounted to the prewired TTX400 section with 7-wire ribbon cable.The TMX400 units with conventional ballasts are supplied with an electrical connector, starters, any necessary capacitor and lampholders. For more control options the TMX400 can be equipped with DALI ballasts. Especially in combination with Linesense controls DALI solutions offer even greater control and energy savings.

TMX400 is deliverable in versions with in-built 3-hour or 1-hour emergency lighting. For configuration of both emergency lighting and regulation or DALI,TTX400 9-wires is to be used with TMX400 9.The new solution of standard TTX400 7-wires with new units TMX400 C-2R is recommended.

	TTX400 TL-D
	Electrical units
Type	TMX400
Light source	Fluorescent:
	1 x or 2 x MASTER TL-D / G13 / 36, 58 W
Gear	Electro magnetic (low loss), 230 V / 50 Hz:
	Inductive (I)
	Inductive with possible mounting of capacitor in
	parallel (IKP)
	Inductive, parallel compensated (IC)
	Electronic, 220 - 240 V / 50 - 60 Hz:
	High Frequency Performer (HFP)
	High Frequency Regulator (HFR)
	High Frequency Regulator, DALI and Touch
	(HFR-TD)
Option	Emergency lighting:
	1 hour (EL1), 3 hours (EL3)
	Master/Slave:
	1 master + 1 slave (M/S)
	both master and slave (M-S)
	2-lamps lampholder with small width (F32)
	HFR/HFR-TD with emergency lighting:TMX400 9
	for trunking 9 wires or preferably TMX400 C-2R
	to be used with TTX400 7-wires (thereby in case
	of non-continuous lightline, to order throughwiring
	/ ZTX400 C1300-2 or C1600-2 as accessory)
Material	Sheet steel, white
Installation	Click-in fixation (both mechanical and electrical
	connection) on trunking TTX400 with 5- or 7-wire
	ribbon cable
Accessory	Blind covers
	Throughwiring set to be used in combination with
	TMX400 C-2R onto TTX400 7, in the case of
	non-continuous lightline (ZTX400 C1300-2 for
	1 section 28/54W; ZTX400 C1600 for 1 section
	35/49/80 W)

Where relevant, for detailed descriptions of Lighting Controls we refer you to chapter 11, and descriptions for e.g. optics/optical covers, lamps data, photometrical diagrams, etc. to the respective sections in chapter 12.

8.52 Light-line systems Philips indoor luminaires