Additional information | 12 |
No sound
Symptom | Cause | Remedy | |
No sound is output when an | • Improper connections. | • Make sure you have properly connected the component | |
input source is selected. |
| to the corresponding input on the back of the receiver | |
No sound output from the front |
| (see Connecting up on page 14). | |
speakers. |
|
| |
• Sound is muted or the volume is turned | • Press MUTE or adjust the volume accordingly. | ||
| |||
| down. |
| |
|
|
| |
| • Speakers are turned off or selected | • Press SPEAKERS to select the proper speaker set (see | |
| improperly with the SPEAKERS switch. | Switching the speaker system on page 56). | |
|
|
| |
| • The input signal type is incorrect. | • Press SIGNAL SELECT to select the proper input signal | |
|
| (see Choosing the input signal on page 33). | |
|
|
| |
| • The multichannel analog inputs are | • Press MULTI CH IN again (see Selecting the | |
| selected. | multichannel analog inputs on page 37). | |
|
|
| |
| • The front speakers aren’t connected | • See Connecting the speakers on page 20 to connect | |
| properly. | them properly. | |
|
|
| |
No sound from the surround or | • Speaker settings are incorrect. (for | • Check you speaker settings in Speaker Setting on | |
center speakers. | example, they have been set to NO). | page 44. | |
|
|
| |
| • The surround and/or center levels are | • Check the levels in Channel Level on page 45. | |
| turned down. |
| |
|
|
| |
| • The surround and/or center speakers are | • Check Connecting the speakers on page 20 to make sure | |
| disconnected. | the speakers are connected correctly. | |
|
|
| |
| • The STEREO listening mode has been | • Choose a surround listening mode (see Listening in | |
| selected. | surround sound on page 30). | |
|
|
| |
No sound from surround back | • Surround back speakers are set to NO. | • Set the surround back speakers to LARGE or SMALL | |
speakers. |
| (see Speaker Setting on page 44). | |
|
|
| |
| • The Extended mode is switched to AUTO or | • Set to Extended ON (see Using the surround back | |
| OFF. | channel (Extended mode) on page 34). | |
|
|
| |
| • The source is not a 6.1 channel playback | • Switch the Extended mode to Extended ON (see Using | |
| source. | the surround back channel (Extended mode) on page 34) | |
|
| and choose a surround listening mode (see Listening in | |
|
| surround sound on page 30). | |
|
|
| |
| • The surround back speakers are | • Check Connecting the speakers on page 20 to make sure | |
| disconnected. | the speakers are connected correctly. | |
|
|
| |
| • The surround back channel is on the 1 | • Connect the speaker to the surround back left channel | |
| speaker setting, and your speaker is | output (Connecting the speakers on page 20). | |
| connected to the right channel output. |
| |
|
|
| |
| • The Extended mode is switched to AUTO | • You can still listen with surround back sound by setting | |
| and the Dolby Surround EX / DTS ES software | to Extended ON (Using the surround back channel | |
| you’re playing has no flag to indicate it is 6.1 | (Extended mode) on page 34). | |
| compatible. |
| |
|
|
| |
No sound from subwoofer. | • The subwoofer is disconnected or switched | • Connect or switch on the subwoofer (see Connecting | |
| off. | the speakers on page 20). | |
|
| • Make sure the sleep function on your subwoofer isn’t | |
|
| activated. | |
|
|
| |
| • The subwoofer's settings are incorrect. | • Set the subwoofer (see Speaker Setting on page 44) to | |
|
| YES or PLUS. |
• The crossover frequency is set too low.
•Set the crossover frequency to a (higher) frequency that matches your speaker characteristics (see Crossover Network on page 45)
• There is very little low frequency information | • Change your subwoofer setting to one of the following in |
in your source. | the Speaker Setting on page 44: |
| Front: SMALL / Subwoofer: YES |
| Front: LARGE / Subwoofer: PLUS |
|
|
• The LFE channel is switched off. | • See LFE Attenuator Setup on page 66 to adjust the |
| setting. |
• The subwoofer's levels are too low.
•See Channel Level on page 45 to check the speaker levels.
•Check the volume control on the subwoofer to make sure it is turned up.
69
En