06The System Setup menu
Fine Channel Level
• Default setting: 0dB (all channels)
You can achieve better surround sound by properly adjusting the overall balance of your speaker system. The following setting can help you make detailed adjustments that you may not achieve using the Manual speaker setup on page 43.
1Select ‘Fine Ch Level’ from the Manual MCACC setup menu.
The volume increases to the 0dB reference level.
3.MANUAL MCACC |
|
| 3a.Fine Channel Level | |
[ |
| ] |
|
|
a .Fine Ch Level |
|
| ||
[ | b .Fine Ch Distance | ] |
|
|
[ c .EQ AUTO Setting | ] |
| Please Wait | |
[ d .EQ Data Copy | ] |
| ||
[ e .EQ CUSTOM1 Adjust | ] |
| Caution!! | |
[ f .EQ CUSTOM2 Adjust | ] |
| ||
[ g .EQ Data Check | ] |
| Test tone is | |
|
|
|
| output loudly. |
|
|
|
| Return:Cancel |
|
|
|
|
|
2 Adjust the level of the left channel.
This will be the reference speaker level, so you may want to keep the level around 0dB so that you’ll have plenty of room to adjust the other speaker levels.
3a.Fine Channel Level
Left 
[ + 0.5dB ]
Enter:Next
Return:Cancel
• After pressing ENTER, test tones will be output
3Select each channel in turn and adjust the levels (+/– 10dB) as necessary.
Use (cursor left/right) to adjust the volume of the speaker you selected to match the reference speaker. When it sounds like both tones are the same volume, press ENTER to confirm and continue to the next channel.
3a.Fine Channel Level
Ref:Left |
|
| + 0.5dB | |
Right |
| [ | + 1.0dB | ] |
Center |
| [ | 0.0dB] |
|
Surround | L | [ | 0.0dB] | |
Surround | R | [ | 0.0dB] | |
Surr Back | L | [ | 0.0dB] | |
Surr Back | R | [ | 0.0dB] | |
Sub Woofer |
| [ | 0.0dB] | |
Return:Finish
•For comparison purposes, the reference speaker will change depending on which speaker you select.
•If you want to go back and adjust a channel, simply
use | (cursor up/down) to select it. |
4 When you're finished, press RETURN.
You will return to the Manual MCACC setup menu.
Fine Channel Distance
• Default setting: 10.0 ft (all channels)
For proper sound depth and separation with your system, it is necessary to add a slight bit of delay to some speakers so that all sounds will arrive at the listening position at the same time. The following setting can help you make detailed adjustments that you may not achieve using the Manual speaker setup below.
1Select ‘Fine Ch Distance’ from the Manual MCACC setup menu.
3.MANUAL MCACC |
|
| 3b.Fine Channel Distance | |
[ a .Fine Ch Level | ] |
|
| |
[ | b .Fine Ch Distance | ] |
|
|
[ | c .EQ AUTO Setting | ] |
| Please Wait |
[ d .EQ Data Copy | ] |
| ||
[ e .EQ CUSTOM1 Adjust | ] |
| Caution!! | |
[ f .EQ CUSTOM2 Adjust | ] |
| ||
[ g .EQ Data Check | ] |
| Test tone is | |
|
|
|
| output loudly. |
|
|
|
| Return:Cancel |
|
|
|
|
|
2Adjust the distance of the left channel from the listening position.
3b.Fine Channel Distance
Left | [ 10.0ft ] |
Enter:Next
Return:Cancel
3Select each channel in turn and adjust the distance as necessary.
Use (cursor left/right) to adjust the delay of the speaker you selected to match the reference speaker. The delay is measured in terms of speaker distance from
0.5to 45.0 feet.
3b.Fine Channel Distance
Ref:Left |
|
| 10.0ft | |
Right |
| [ | 10.0ft | ] |
Center |
| [ | 10.0ft | ] |
Surround | L | [ | 10.0ft ] | |
Surround | R | [ | 10.0ft ] | |
Surr Back | L | [ | 10.0ft ] | |
Surr Back | R | [ | 10.0ft ] | |
Sub Woofer |
| [ | 10.0ft ] | |
Return:Finish
Listen to the reference speaker and use it to measure the target channel. From the listening position, face the two speakers with your arms outstretched pointing at each speaker. Try to make the two tones sound as if they are arriving simultaneously at a position slightly in front of you and between your arm span.
40
En
