Pioneer VSX-52TX manual 07Using the tuner Saving station presets, Naming station presets

07Using the tuner

Saving station presets

Naming station presets

If you often listen to a particular radio station, it's		For easier identification, you can name your station
convenient to have the receiver store the frequency for		presets.
easy recall whenever you want to listen to that station.		1 Choose the station preset you want to name.
This saves the effort of manually tuning in each time. This
		See Listening to station presets below for how to do this.
unit can memorize up to 30 stations, stored in three
		2 Press T.EDIT (TUNER EDIT).
banks, or classes, (A, B and C) of 10 stations each. When
saving an FM frequency, the MPX setting (see page 47) is		The display shows STATION NAME, then a blinking
also stored.		cursor at the first character position.
		3 Input the name you want.
		Choose from the following characters for a name up to
	LISTENING MODE	four characters long.
STANDBY/ON	SELECT
	ENTER	ABCDEFGHIJKLMNOPQRSTUVWXYZ
MULTI JOG		abcdefghijklmnopqrstuvwxyz
		0123456789
		!”#$%&’()∗+,–./:;<=>?@[ \ ]^_{} ˜

TUNER	TUNING/			MIDNIGHT/	ACOUSTIC		DIALOG	MULTI CH	SIGNAL	EXTENDED	SPEAKERS
EDIT	STATION	BAND	MPX	LOUDNESS	TONE	EQ	ENHANCEMENT	IN	SELECT	MODE
TUNER	MULTI				MULTI
CONTROL
	JOG				JOG
		MULTI ROOM						VIDEO2 INPUT
SYSTEM					MCACC
SETUP	RETURN	CONTROL	ON/OFF		SETUP MIC
MULTI JOG		MULTI JOG
PHONES
							DIGITAL IN	S-VIDEO	VIDEO	L AUDIO	R

RECEIVER	INPUT		SOURCE
	SELECT
			INPUT ATT		FL DIMMER		SR
				+10			DISC
							ENTER
			D.ACCESS				CLASS
			TOP MENU				MENU
					TUNE
			DTV MENU	ST	ENTER		ST
			T.EDIT				BAND
			SYSTEM		TUNE
			GUIDE SETUP		TV CONTROL		RETURN
DVD/LD	TV/SAT	DVR/VCR	TV CONT
	MULTI CONTROL		TVVOL		INPUT	TV CH	VOL
CD	CD-R/TAPE	TUNER	RECEIVER		SELECT
			DTVON/OFF		REC	DTVINFO	MUTE
			TUNER			RECSTOP
			DISPLAY
			MPX	CHRETURN		HDD	DVD
			AUDIO		SUBTITLE
INPUT ATT	FL DIMMER		SR			CH	CH
			DISC

1 Tune to a station you want to memorize.

See Listening to the radio on page 47 for more on this.

2 Press T.EDIT (TUNER EDIT).

The display shows STATION MEMORY, then a blinking memory class.

3Press CLASS to select one of the three classes then press ST +/– (STATION +/–) to select the station preset you want.

You can also use the number buttons or the MULTI JOG dial (front panel) to select a station preset.

4Press ENTER.

After pressing ENTER, the preset class and number stop blinking and the receiver stores the station.

•Use the MULTI JOG dial (front panel) or the ST +/– buttons (remote) to select characters.

•Press ENTER to confirm a character. If no character is input, a space is input.

•The name is stored when ENTER is pressed after choosing the fourth character.

Tip

•To erase a station name, simply repeat steps 1-3 and input four spaces instead of a name.

•Once you have named a station preset, you can press TUNER DISPLAY when listening to a station to switch the display between name and frequency.

Listening to station presets

You will need to have some presets stored to do this. See Saving station presets above if you haven’t done this already.

1Press TUNER to select the tuner.

2Press CLASS to select the class in which the station is stored.

Press repeatedly to cycle through classes A, B and C.

3Press ST +/– (STATION +/–) to select the station preset you want.

•You can also use the number buttons on the remote control to recall the station preset.

Note

•If the receiver is left disconnected from the AC power outlet for over a month, the station memories will be lost and will have to be reprogrammed.

48

En