Pioneer VSX-72TXV-S Using Professional Acoustic Calibration EQ, Select an option and press Enter

The System Setup menu 07

Using Professional Acoustic Calibration EQ

1 Select ‘EQ Professional’ then press ENTER.

3.Manual		MCACC		3e.EQ Professional
	a.Fine	Ch	Level
					1.Reverb	Measurement
	b.Fine	SP	Distance		2.Reverb	View
	c.Standing		Wave		3.Reverb	Output	PC
	d.EQ	Adjust			4.Advanced EQ		Setup
	e.EQ	Professional
			￿:Return		ENTER:Next		￿:Return

2Select an option and press ENTER.

•Reverb Measurement – Use this to measure the reverb characteristics of your room (for graphical output using a PC, see Connecting a PC for Advanced MCACC output on page 60 to connect an RS-232C cable before selecting this option).

•Reverb View – You can check the reverb measurements made for specified frequency ranges in each channel.

•Reverb Output PC – See Connecting a PC for Advanced MCACC output on page 60 for more on this.

•Advanced EQ Setup – Use this to select the time period that will be used for frequency adjustment and calibration, based on the reverb measurement of your listening area. Note that customizing system calibration using this setup will alter the settings you made in Automatically setting up for surround sound (MCACC) on page 7 or Automatic MCACC (Expert) on page 32 and is not necessary if you’re satisfied with these settings.

3If you selected ‘Reverb Measurement’, select EQ ON or OFF and then OK.

3e1.Reverb Measurement		3e1.Reverb Measurement
MCACC: M1.MEMORY 1		Now Analyzing…			(1/5)
Measure with
	EQ OFF	M1. MEMORY 1		EQ:ON
Setting Start?	[OK]	Ambient Noise		[	OK	]
		Microphone	[			]
		Speaker Level	[		]
		Delay Check	[		]
		Reverb	[		]
	￿:Cancel		￿:Cancel

When the reverb measurement is finished, you can select Reverb View to see the results on-screen. See Professional Calibration EQ graphical output on page 77 for troubleshooting information.

4If you selected ‘Reverb View’, you can check the reverb characteristics for each channel. Press RETURN when you’re done.

3e2.Reverb View
	M1 : EQ OFF Ch	[	L ]
dB	Fq	[	40Hz	]
0	80	160ms
		￿:Return

This appears according to the setting you chose in Reverb Measurement (step 3 above). Use the buttons to select the channel and the frequency you want

to check. Use the buttons to go back and forth between the two. Note that the markers on the vertical axis indicate decibels in 2dB steps.

5If you selected ‘Advanced EQ Setup’, input the time setting you want to use for calibration, then select ‘Go’. Select ‘Start’ from the next screen.

Based on the reverb measurement above, you can choose the time period that will be used for the final frequency adjustment and calibration. Even though you can make this setting without reverb measurement, it is best to use the measurement results as a reference for your time setting. For an optimal system calibration based on the direct sound coming from the speakers, we recommend using the 20–40mssetting.

3e4.	Adv. EQ Setup		(1/2)	3e4. Adv. EQ Setup	(2/2)
	Ch
			L	( Back )
dB	Fq	[	40Hz ]	EQ Type
	Tm	[60~80ms]		[ALL CH	ADJUST]
				Multi-Point		NO
				Setting Start?		[OK]
				Please place the mic
0	80	160ms		at your 2nd reference
				point.
(	Next)		￿:Cancel
				￿ : Cancel

The following options determine how the reverb characteristics of your listening area are displayed in Reverb View and Reverb Output PC:

•EQ OFF – You will see the reverb characteristics of your listening area without the equalization performed by this receiver (before calibration).

•EQ ON – You will see the reverb characteristics of your listening area with the equalization performed by this receiver (after calibration).1 Note that the EQ response may not appear entirely flat due to adjustments necessary for your listening area.

Use the	buttons to select the channel, frequency,
and time setting. Use the		buttons to switch
between them.

You can switch between your connected speakers (excluding the subwoofer), and display the measurements for the following frequencies: 63Hz, 125 Hz, 250Hz, 500Hz, 1kHz, 2kHz, 4kHz, 8kHz and 16kHz.

Select the setting from the following time periods (in milliseconds): 0–20ms, 10–30ms, 20–40ms, 30–50ms, 40–60ms, 50–70ms and 60–80ms. This setting will be applied to all channels during calibration.

When you’re finished, select OK. It will take about 1–4 minutes for the calibration to finish.

Note

1The calibration corresponding to the currently selected MCACC preset will be used when EQ ON is selected. To use another MCACC preset, exit the System Setup menu and press MCACC to select it before pressing SETUP.

39

En