Pioneer VSX-72TXV, VSX-74TXVI manual Display, Professional Calibration EQ graphical output, 96kHz

Additional information 12

Symptom	Remedy
The display shows KEY LOCK	• With the receiver in standby, press STANDBY/ON while holding down the MULTI-ROOM&SOURCE
ON when you try to make	CONTROL button to disable the key lock.
settings.
Most recent settings have been	• The power cord was disconnected from the wall while adjusting this setting.
erased.

Professional Calibration EQ graphical output

Symptom	Remedy
The EQ response displayed in the	• There are cases where the graph does not appear flat (even when selecting ALL CH ADJUST in the Auto
graphical output following	MCACC Setup) due to adjustments made to compensate for room characteristics to achieve optimal sound.
calibration does not appear	• Areas of the graph may appear identical (before and after) when there is little or no adjustment needed.
entirely flat.	• The graph may appear to have shifted vertically when comparing before and after measurements.
EQ adjustments made using the	• Despite level adjustments being made, the filters used for analysis may not display these adjustments in
Manual MCACC setup on	the graphical output. However, these adjustments are taken this into account by the filters dedicated to
page 35 do not appear to change	overall system calibration.
the graphical output.
Lower frequency response	• Low frequencies used in bass management (the subwoofer channel) will not change for speakers that
curves do not seem to have been	have been specified as SMALL in the configuration, or do not output these frequencies.
calibrated for SMALL speakers.	• Calibration is performed, but due to your speakers’ low frequency limitations, no measurable sound is
	output for display.
Graphical output data seems to	• If the power is switched off, the measurement data for graphical output to a PC is cleared.
have disappeared.

Display

Symptom	Remedy
The display is dark or off.	• Press DIMMER on the remote control repeatedly to select a different brightness.
After making an adjustment the	• Press DIMMER on the remote control repeatedly to select a different brightness.
display goes off.
You can't get DIGITAL to display	• Check the digital connections and make sure that the digital inputs are assigned correctly (see The Input
when using the SIGNAL SELECT	Setup menu on page 61).
button.	• If the multichannel analog inputs are selected, select a different input source.
The Dolby/DTS indicator doesn't	• These indicators do dot light if playback is paused.
light when playing Dolby/DTS	• Check the playback (especially the digital output) settings of the source component.
software.
When playing a DVD-Audio disc,	• This is not a malfunction. 96 kHz audio from DVD-Audio discs is only output from the analog outputs of
the DVD player display shows	the DVD player. This receiver cannot show the playback sample rate when using the analog inputs.
96 kHz. However, the receiver’s
display does not.
During playback of a DTS 96/24	• Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on page 28).
source, the display doesn't show
96kHz.
When playing Dolby Digital or	• Check that the player is connected using a digital connection.
DTS sources, the receiver’s	• Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on page 28).
format indicators do not light.	• Check that the player isn’t set up so that Dolby Digital and DTS sources are converted to PCM.
	• Ensure that if there are several audio tracks on the disc, the Dolby Digital or DTS is selected.
When playing certain discs, none	• The disc may not contain 5.1/6.1 channel material. Check the disc packaging for more on what audio
of the receiver’s format	tracks are recorded on the disc.
indicators light.
When playing a disc, the	• Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on page 28).
2 PL II or Neo:6 indicator lights	• If a two channel soundtrack is currently playing (including Dolby Surround encoded), then this is not a
on the receiver.	malfunction. Check the disc packaging for details about the audio tracks available.

77

En